GRAUPNER mz-24 Pro Programming Manual page 155

Basic operating steps
• ST OFF / ST ON buttons
Touch this button to turn the graphic and numeric
display of the control stick position on or off.
In switch on stand through the control elements
(throttle/pitch control stick) a vertical green line is
moved synchronously in the graph between the
two endpoints "L" and "H". The momentary con-
trol stick position is also displayed numerically in
the line "IN"(put) (-100 % to +100 %). The inter-
section of this line with the curve is identified as
"OUT"(put) and can be varied at the support points
between -125% and +125%. The control signal
which is changed in this way then affects all of the
following mixing and coupling functions.
In the following example, the control stick is exact-
ly halfway between the middle and end of its path,
at +50% of the control path, and generates an out-
put signal that is also +50% due to the linear char-
acteristic.
Between the two endpoints "L" and "H", up to 5
additional support points can be set, and the dis-
tance between neighboring support points may
not be less than approximately 25%.
BACK PHASE 1 PITCHK
Pitch min. FORWARD
Curve OFF
IN +050%
OUT +050%
POINT ? 000%
ST ON X-axis Y-axis
• ENT button
Move the control stick. As long as a "?" is next to
the "POINT", you can set the next support point by
touching the ENT button.
At the same time, a green point appears at the in-
tersection between the yellow and green lines:
BACK
Pitch min.
Once the green line is moved with the control stick
around the point, it becomes red, the "?" is re-
placed with a number, and the point value appears
in the value field to the right of the support point
number:
BACK
Pitch min.
The sequence in which the up to 5 points between
the end points "L" and "H" are generated does not
SERVO matter since the support points are automatically
renumbered sequentially from left to right after one
TRIM
support point is set or deleted, for example:
INC
BACK
Pitch min
DEC
ENT
PHASE 1 PIT>>TAIL SERVO
TRIM
FORWARD
Curve OFF
+050% INC
IN
OUT +050%
Touch
DEC
POINT ? 000%
ST ON X-axis Y-axis ENT
PHASE 1 PIT.CRV SERVO
TRIM
FORWARD
Curve OFF
INC
ON +050%
OUT +050%
POINT 1 +050% DEC
ST ON X-axis Y-axis ENT
PHASE 1 PIT.CRV SERVO
TRIM
FORWARD
Curve OFF
INC
IN –050%
OUT –050%
DEC
POINT 1 –050%
ST ON X-axis Y-axis ENT
Deleting a support point
In order to delete the set support points 1 to 5,
move the vertical green line with the control stick
next to the relevant support point. Once the sup-
port point number appears along with the associ-
ated value in the line "POINT" and the point is red
(see the screen-shot below), you can delete it by
touching the ENT button, for example:
BACK PHASE 1 PIT.CRV
Pitch min FORWARD
KURVE OFF
IN 000%
OUT 000%
POINT 2
ST ON X-axis
BACK PHASE 1 PIT.CRV
Pitch min FORWARD
CURVE OFF
IN 000%
OUT 000%
POINT ?
ST ON X-axis
Changing the support point value
• X-axis button
Activate this function by touching the button at
the bottom edge of the display. The button color
changes from black to blue:
You can then move an active (red) point to the right
with the + button, and to the left with the
ton, for example:
Function menu | Helicopter model - Pitch curve
SERVO
TRIM
INC
Touch
000% DEC
Y-axis ENT
SERVO
TRIM
INC
DEC
000%
Y-axis ENT
(X-axis)
– but-
155