Ctrl/Sw Option - GRAUPNER mz-24 Pro Programming Manual

Set" a switch or a con-
If in the sub-menu "CTL
trol has been assigned to the output "CH6",
for example the left proportional control lever
"SL2" ...
BACK PHASE 1 CTL Set
CH 5. NONE 000% +100% +100%
CH 6. SL 2 000% +100% +100%
CH 7. NONE 000% +100% +100%
CH 8. NONE 000% +100% +100%
CTL OFFSET – Travel +
... then all the provided flaps move in the po-
sition corresponding to the control position
("CTL Set"), offset value and travel setting so
as ("Flap MIX") RATE and offset values of the
respective flaps positions.
Notice
Set therefore the clarity as far as possible
only in one of the involved sub-menus val-
ue.
• "ACT" = ON
As long as "ACT" is activated ...
BACK PHASE 1 Flap Set
ACT ON CTL ON
AILE1 AILE2
RATE A 000% 000%
RATE B 000% 000%
... only the standard or previously customized
offset values of the "aileron" option of the
MIX" sub-menu are valid ...
BACK
FLAP
SERVO RATE A
RATE B
NEXT
OFFSET
INC
... so as the following described RATE setting
RES
of the "AILERON" display page of the
DEC
set" sub-menu ...
BACK
ACT
RATE A
RATE B
... on the standard flap servos 6 and 7 so as 9
and 10, or in case of a model with only one flap
servo only to the servo 6.
If in the sub-menu
trol has been assigned to the output "CH6",
for example the left proportional control lever
"SL2" so as an offset value, e.g. ...
SERVO
BACK
NEXT
INC
K 5.
RES
K 6.
DEC
K 7.
K 8.
"Flap
... then all the provided flaps move to the con-
trol position
PHASE 1 FLAP MIX SERVO
INC
FLAP1 FLAP3 FLAP4 FLAP2
+100% +100% +100% +100% RES
DEC
+100% +100% +100% +100%
000% 000% 000% 000%
"Flap
PHASE 1 Flap set SERVO
ON CTL ON
NEXT
FLAP1 FLAP2 INC
000% 000% RES
000% 000% DEC
"CTL Set" a switch or a con-
PHASE 1 CTL Set SERVO
NONE 000% +100% +100% NEXT
SL 2 +015% INC
+100% +100%
NONE 000% +100% +100% RES
DEC
NONE 000% +100% +100%
CTL OFFSET – TRAVEL+
("CTL Set"),
Offset and travel settings so as to the RATE val-
ues of the following described aileron displays
set" sub menu. And all the flaps
of the "Flap
accordingly to the addiction of
control position, offset value and travel settings
so as ("Flap MIX") offset and the RATE values
of the following described aileron display of the
"Flap set" sub-menu.
Notice
Set the clarity as far as possible only in one
of the involved sub-menus value.
In the displays described below, you
specify the effect of the control elements assigned
to channel 6 in the "CTL Set" sub-menu, in the
form of a phase trim on the positions of the aile-
rons, flaps, and possibly the elevators.

• Ctrl/sw option

In the value field in the Ctrl/sw column, you as-
sign a control or control switch for a specific phase
to the mixer as described in the section
and switch assignment, for example in the phase
"THERMAL":
BACK THERMAL Flap set
ACT ON CTL
AILE1
000%
RATE A
RATE B 000%
Function menu | Airplane models - Flaps settings
("CTL Set")
(control/switch)
Control
SERVO
SW 6
NEXT
INC
AILE2
RES
000%
000% DEC
197