Rx Free Mixer - GRAUPNER mz-24 Pro Programming Manual

BACK Telemetry
RECV
RX FAIL SAFE V6.35<>
>OUTPUT CH: 01
GENE
INPUT CH: 01
MODE : HOLD ELEC
F.S.POS : 1234µsec
VARIO
DELAY : 0.25sec
FAIL SAFE ALL: NO GPS
POSITION : 1234µsec
ESC
Turn off the transmitter and check the fail safe posi-
tions by checking the servo travel.
"Fail safe" in combination with "Channel mapping"
To make sure that mapped servos react in the same
way even in a malfunction, that is, servos that are
controlled by common control channel (INPUT CH),
the corresponding settings of the INPUT CH deter-
mine the behavior of mapped servos.
If for example servo connections 6, 7 and 8 of a re-
ceiver are mapped by assigning the same control
channel "04" as the INPUT CH to OUTPUT CH (servo
connections of the receiver) 06, 07 and 08...
BACK Telemetry
RX FAIL SAFE V6.35<> RECV
>OUTPUT CH: 06
GENE
INPUT CH: 04
MODE : HOLD
ELEC
F.S.POS : 1500µsec
VARIO
DELAY : 0.25sec
FAIL SAFE ALL: NO
GPS
POSITION : 1500µsec
ESC
BACK
Telemetry
RX FAIL SAFE V6.35<>
EMPF
>OUTPUT CH: 07
GAM
INPUT CH: 04
MODE : HOLD
EAM
F.S.POS : 1500µsec
VARIO
DELAY : 0.25sec
FAIL SAFE ALL: NO
GPS
POSITION : 1500µsec
ESC
106 Base menu - Telemetry | SETTINGS/DISPLAYS
BACK
ESC RX FAIL SAFE V6.35<>
>OUTPUT CH: 08
DEC
INPUT CH:
INC MODE : HOLD
F.S.POS : 1500µsec
ENT
DELAY : 0.25sec
FAIL SAFE ALL: NO
SET
POSITION : 1500µsec
... then INPUT CH 04 determines the fail safe behav-
ior of these three servos connected to control channel
4 fully independent of the settings of the respective
OUTPUT CH:
BACK
RX FAIL SAFE V6.35<>
>OUTPUT CH: 04
INPUT CH: 04
MODE :
F.S.POS : 1500µsec
DELAY : 0.25sec
FAIL SAFE ALL: NO
POSITION : 1500µsec
This is also true when INPUT CH 01 is used for map-
ping:
ESC
BACK
DEC
RX FAIL SAFE V6.35<>
>OUTPUT CH: 04
INC
INPUT CH:
ENT
MODE : FAI-SAFE
F.S.POS : 1500µsec
SET
DELAY : 0.25sec
FAIL SAFE ALL: NO
POSITION : 1500µsec
In this case, servo connection 04 reacts according to
ESC
the fail safe settings of CH 01.
DEC
The reaction time or delay set in the "DELAY" line
INC
contrastingly applies uniformly to all channels set to
ENT
"FAI(L) SAFE".
SET
Telemetry
RECV ESC
GENE DEC
04
INC
ELEC
VARIO ENT
GPS SET
ESC
Telemetry
RECV ESC
GENE DEC
FAI-SAFE ELEC INC
VARIO ENT
GPS SET
ESC
Telemetry
RECV ESC
DEC
GENE
01
ELEC INC
VARIO ENT
GPS SET
ESC

RX FREE MIXER

BACK
Telemetry
RX FREE MIXERV6.35<>
RECV
>MIXER : 1
GENE
MASTER CH: 00
SLAVE CH : 00
ELEC
S-TRAVEL–: 100
VARIO
S-TRAVEL+: 100
RX WING MIXER
GPS
TAIL TYPE: NORMAL
ESC
Value Explanation
Vx.xx Firmware version
of the receiver
MIXER Mixer selection
MASTER CH Signal source or
source channel
SLAVE CH Target channel
S-TRAVEL– Mixing on the "–"
side of the servo
travel in percenta-
ge servo travel
S-TRAVEL+ Mixing on the "–"
side of the servo
travel in percenta-
ge servo travel
RX WING Tail type
MIXER
TAIL TYPE
ESC
DEC
INC
ENT
SET
Possible set-
tings
None
1 ... 5
0, 1 ... depen-
ding on the
receiver
0, 1 ... depen-
ding on the
receiver
0 ... 100 %
0 ... 100 %
NORMAL,
V-TAIL (V-LW)
ELEVON
(elevator/aileron
mixer for delta
and flying wing)