Pitch Curve; "Pitch Min" Line; Setting The Pitch Curve - GRAUPNER mz-24 Pro Programming Manual

Pitch curve

Phase-specifi c setting of the pitch control curve
In the basic transmitter display, use your fi nger or the
provided stylus to touch the gear icon labeled "F":
000%
000:00.0
000 000
mz
0:01:23 000:00.0
Touch
M - 3
000 000
PHASE 1
Starlet
BATT TIME 00: 01: 23
000
The display switches to the blue function menu. Touch
the menu item "PIT.CRV".
BACK BASE FUNCTION
Phase D/R,EXP PIT.CRV THR.CRV
Touch
THR.HOLD Swash S.Limit S.MIX
Prog.MIX Trainer PIT>>TAIL Logical sw
For the setting of the pitch curve there is a curve mixer
available in every fl ight phase. In this mixer can how-
ever only be programmed if required also not linear
mixer actions analog to the control stick travels.

"Pitch min" line

In the helicopter program for the mz-24 HoTT Pro
transmitter, the "rear" throttle position is the "Pitch
min." position by default.
Through this option you can easily reverse the control
direction of the pitch control stick from the standard
pre-set position "pitch min back" to "pitch min for-
ward", and vice versa, by tapping on the
FORWARD button in the "Pitch min" line:
154 Function menu | Helicopter model - Pitch curve
000%
4.2V
The warning note appears:
000
SYSTEM
Gyr/Gover
Touch NO to terminate the procedure. Touch
THR.MIX
to confi rm the procedure which changes the direction
of travel of the pitch control stick:
Sequence
Such an inverted control signal acts on all following
mixed and coupling functions and the active Power
OFF time of the Thro Position.
Phase-dependent settings of the pitch curves
BACK or
The here mentioned sub-menu offers the possibility
of phase specifi c settings. Recognizable on the top
left side of the display in green color is displayed the
phase name.
BACK PHASE 1 PIT.CRV SERVO
TRIM
Pitch min BACK
CURVE OFF
Touch
INC
IN –100%
OUT –100%
DEC
POINT L –100%
ST OFF X-axis Y-axis ENT
BACK PHASE 1 PIT.CRV SERVO
TRIM
Pitch min BACK
KURVE AUS
Warning
INC
EIN SURE? –100%
AUS –100%
YES NO
POINT L –100% DEC
ST OFF X-axis Y-axis ENT
BACK PHASE 1 PIT.CRV SERVO
TRIM
Pitch min FORWARD
Curve OFF
IN –100% INC
OUT –100%
POINT DEC
L –100%
ST OFF X-axis Y-axis ENT
As standard is displayed the name of the phase
1, which is indicated by the name "NORMAL" or
"PHASE 1". As soon as you will have defi ned one or
many other phases in the "PHASE" menu, you will
be able to switch among those phases. Activate the
corresponding switch or switches if desired to switch
between the phases.

Setting the pitch curve

In this display, you can adapt the pitch curve as need-
ed, depending on the phase if desired:
BACK
PHASE 1
Pitch min FORWARD
Curve
IN
OUT
POINT
YES
ST OFF
Notice
In the display graph will be represented the curve
characteristics directly and completely inde-
pendently from the actually selected direction of
the pitch control stick.
The pitch control curve can be specifi ed by up to 7
points, the so-called support points, along the entire
control stick travel.
At the beginning, fewer support points are required to
set the pitch curve. It is, however, highly recommend-
able to start with three support points.
These three endpoints, the two endpoints "Pitch low
(L)" = -100% control travel and "Pitch high (H)" =
+100% control travel, as well as a point to be placed
in the control, center describe a linear characteristic
for the pitch control curve.
SERVO
PIT.CRV
TRIM
OFF
–100% INC
–100%
DEC
L –100%
X-axis Y-axis ENT