Rf On/Off; Rf Type; Range Test - GRAUPNER mz-24 Pro Programming Manual

BACK
Touch the button at the top left of the display
to return to the "Transmitter setting" sub-menu.
Examples
• On a large model, you want to control each aileron
fl ap using two or more servos:
Assign the same input (control channel) to the rele-
vant outputs (servo connections). In this case, as-
sign one of the two default aileron control channels 2
+ 5 as an input depending on the left or right wing.
• On a large model, you want to control the rudder
using two or more servos:
Assign the same input (control channel) to the rele-
vant outputs (servo connections). In this case, de-
fault rudder channel 4.
Notices
• The maximum number of available lines (out-
puts) corresponds to the maximum number of
servos that can be connected to each receiv-
er.
• You can use the "Transmitter
tion, of the mz-24 HoTT Pro transmitter to
switch the transmitter control function as de-
sired, or assign the same control function to
several outputs. For the sake of clarity, it is
strongly recommended to only use one of the
two options.
Assigning one channel to two receivers
As mentioned above, you can use the "receiver out-
put" option to distribute the 12 control channels of
the mz-24 HoTT Pro transmitter to two receivers as
desired.
The numbering of the outputs (servo connections) and
the maximum number of available lines (outputs) cor-
responds to the maximum number of servos that can
be connected to the respective receivers. Follow the
same procedure as above.

RF ON/OFF

In this line, you can manually turn the transmitter's RF
transmission off and back while the transmitter is cur-
rently turned on, For example to be able to chance
model memory or to change model type .
Notice
The next time the transmitter is turned on or a
model is switched, the OFF setting is reversed.
To manually turn the high-frequency transmis-
sion of your transmitter on or off, touch the corre-
sponding button in the "RF ON/OFF" line:
BACK
BIND ON/OFF
output" op-
TX OUT SET
RF ON/OFF

RANGE TEST

DSC OUTPUT
Tip
Alternatively it is also possible to tap on the RF switch
symbol in the basic menu of the transmitter to recall a
function similar to the RF emission.
TX ctl
RX1 RX2
12CH OFF
SET SET
ON NORMAL

RF TYPE

OFF 99sec
Touch
PPM10 OFF
AUTOLOG
000%
000:00.0
Touch 000 000
mz
0:01:23 000:00.0
M - 1
000 000
PHASE 1
MODELLNAME 1
BATT TIME 00: 01: 23
000
RF type
The specifi c RF type needs to be set to satisfy the
relevant guidelines (FCC, ETSI, IC, etc.).
To switch your transmitter's country setting between
"NORMAL" or "USA", touch the button to the right of
"RF type":
BACK TX ctl
RX1 RX2
12CH OFF
BIND ON/OFF
SET SET
TX OUT SET
ON
RF ON/OFF RF TYPE
RANGE TEST OFF 99sec
PPM10
DSC OUTPUT AUTOLOG
RANGE TEST
The integrated range test reduces the transmitter out-
put so that you can perform a function test at a dis-
tance of less the 100 m.
Perform the range test for the Graupner-HoTT system
according to the following instructions. It is useful to
have an assistant to help you with the range test.
1. Install the receiver(s) already bound to the trans-
mitter into the model as described.
2. Switch the transmitter on and wait until the receiv-
er/s indicate/s a correct function connection. You
are now able to monitor servo movements.
Base menu - Transmitter setting
000%
4.2V
000
(country setting)
NORMAL
Touch
OFF
71