GRAUPNER mz-24 Pro Programming Manual page 195

Notice
The available setting options depend on the
number of fl aps selected in the basic settings of
the actual model.
After you have fi nished making your settings, touch
BACK
the button at the top left to return to the mixer
selection:
BACK
THERMIK FLAP MIX
FLAP TYP ACT SET CTL
Touch
>>
FLAP
AILE >> FLAP ON >> ON
>>
ELEV >> FLAP INH ON
>>
FLAP >> ELEV INH ON
ELEV >> FLAP line
To support the elevator in tight curves and aerobatics,
the fl ap function can be included by controlling the
elevator with this mixer. Select the mixing direction
so that the fl aps move downward when the elevator
is pulled ("up"), and conversely upward when the el-
evator is pushed ("down"), that is, in an opposite di-
rection.
A symmetrical or an asymmetrical effect can be de-
fi ned for each fl ap pair. Values of ±125% are possi-
ble. By default, uniform values of +30% are set for the
aileron...
BACK SPEED Flap MIX
ELEV >> FLAP CTL ON
AILE1 AILE3 AILE4 AILE2
RATE A +030% +030% +030% +030%
RATE B +030% +030% +030% +030%
... and the fl aps:
BACK
ELEV >> FLAP
RATE A
RATE B
SERVO
Adapt the individual values as described under "FLAP
line".
Notice
The available setting options depend on the
number of ailerons and fl aps selected in the basic
settings of the actual model.
After you have fi nished making your settings, touch
BACK
the button at the top left to return to the mixer
selection:
BACK
FLAP TYPE
Touch
FLAP
AILE >> FLAP
RUDD >> FLAP
FLAP >> ELEV
FLAP >> ELEV line
SERVO
When setting fl aps, upward or downward torque can
arise about the transverse axis. It may also be de-
NEXT
sirable for the model to pick up the pace somewhat
INC
when slightly elevating the fl aps. Both of these reac-
RES
tions can be achieved with the mixer.
DEC
When setting the fl aps, you can use this mixer to have
the position of the aileron automatically track the fl aps
depending on the set value.
SERVO
SPEED Flap MIX
CTL ON
NEXT
FLAP1 FLAP2 INC
FLAP3 FLAP4
+030% +030% +030% +030% RES
DEC
+030% +030% +030% +030%
SPEED Flap MIX SERVO
SET
ACT CTL
>>
>>
ON ON
ON >> ON
>>
INH ON
The setting can be symmetrical or asymmetrical to the
neutral point of the fl ap control.
The adjustment range is ±125%. With this mixer,
normal settings lie within the single-digit to low dou-
ble-digit range. By default, 0% is uniformly set:
BACK
SPEED Flap MIX
FLAP >> ELEV CTL
ELEV1
RATE A 000%
RATE B 000%
Adapt the individual values as described at the begin-
ning of this section under "FLAP line".
After you have fi nished making your settings, touch
BACK
the button at the top left to return to the mixer
selection:
BACK SPEED Flap MIX
SET
FLAP TYPE ACT
Touch
>>
FLAP
>>
AILE >> FLAP ON
ELEV >> FLAP ON >>
>>
FLAP >> ELEV ON
BACK
... and by tapping again on the
return to the menu selection:
BACK BASE FUNCTION
Phase D/R,EXPO THR.CRV Idle LOW
Snap roll Aile diff Wing MIX Flap MIX
Airbrake TTrainer Logical sw Sequence
Function menu | Airplane models - Flaps mixer
SERVO
ON
INC
RES
DEC
SERVO
CTL
ON
ON
ON
button you will
SYSTEM
Prog.MIX
Flap set
V-Tail
195