Getting Started; Understanding The Display; Keypad Operation; Ki-Hoa Keypad Rtc - Emerson Powerdrive F300 User Manual

Safety Product Mechanical
information information installation
5

Getting started

This chapter introduces the user interfaces, menu structure and security
levels of the drive.
5.1

Understanding the display

The keypad can only be mounted on the drive.
5.1.1

KI-HOA Keypad RTC

The KI-HOA Keypad RTC display consists of two rows of text. The upper
row shows the drive status or the menu and parameter number currently
being viewed. The lower row of the display line shows the parameter
value or the specific trip type. The last two characters on the first row
may display special indications. If more than one of these indications is
active then the indications are prioritized as shown in Table 5-2.
When the drive is powered up the lower row will show the power up
parameter defined by Parameter Displayed At Power-Up (11.022).
Figure 5-1 KI-HOA Keypad RTC
1
2
AUTO
3
HAND
1. Escape button
2. Auto button
3. Start forward
4. Navigation keys (x4)
5. Off / Reset (red) button
6. Enter button
NOTE
The red stop button is also used to reset the drive.
The parameter value is correctly displayed in the lower row of the
keypad display, see table below.
Table 5-1 Keypad display formats
Display formats
IP Address
MAC Address
Time
Date
Version number
Character
32 bit number with decimal point
16 bit binary number
Powerdrive F300 User Guide
Issue Number: 2
Electrical Getting Basic
installation started parameters the motor
6
5
OFF
Reset
4
Value
127.000.000.000
01ABCDEF2345
12:34:56
31-12-11 or 12-31-11
01.02.02.00
ABCD
21474836.47
0100001011100101
Running NV Media Card
Optimization
Operation
Table 5-2 Active action icon
Active action icon
or
5.2

Keypad operation

5.2.1 Control buttons
The keypad consists of:
• Navigation Keys - Used to navigate the parameter structure and
change parameter values.
• Enter / Mode button - Used to toggle between parameter edit and
view mode.
• Escape / Exit button - Used to exit from parameter edit or view
mode. In parameter edit mode, if parameter values are edited and
the exit button is pressed, the parameter value will be restored to the
value it had on entry to edit mode.
Three control buttons are used to select Hand / Off / Auto modes (see
below).
NOTE
Low battery voltage is indicated by
display. Refer to section 3.13.1 Real time clock battery replacement on
page 66 for information on battery replacement.
Figure 5-2 Display modes on page 104, shows an example of moving
between menus and editing parameters.
5.2.2 Hand / Off / Auto
Hand / Off / Auto functions are enabled if Pr 01.052 is set to a non-zero
value, otherwise the keypad buttons are allocated as follows:
• Blue - Forward/Reverse
AUTO
• Green - Run
• Red - Reset
When Hand / Off / Auto functions are enabled (Pr 01.052 set to either 1,
2 or 3), then the keypad buttons will be allocated as follows:
• Blue - Auto
AUTO
• Green - Hand
• Red - Off/Reset
The value in Pr 01.052 selects Hand/Off/Auto mode on power-up as
shown in Table 5-3.
Table 5-3 Hand/Off/Auto mode
Pr 01.052
0
1
2
3
Onboard Advanced Technical
Diagnostics
PLC parameters data
Description
Accessing non-volatile
media card
Alarm active
Keypad real-time clock
battery low
Drive security active and
locked or unlocked
User program running
Keypad reference active
low battery symbol on the keypad
Power up
Hand/Off/Auto disabled
Auto Mode
Off Mode
See table Table 5-4
UL listing
information
Row Priority
(1=top) in row
1 1
1 2
1 3
1 4
3 1
4 1
103