Table of Contents
Advertisement
Wing Mix
Adjusting mixers
In the basic transmitter display, use a finger or the
provided stylus to touch the gear icon labelled "F":
000%
RX
TX
RX 00.0V
000:00.0
000
000
mz
000:00.0
0:01:23
Touch
M 1
000
000
NORMAL
Graubele
BATT TIME 00: 01: 23
000
The display switches to the blue function menu. Use a
finger or the provided stylus to touch the "Wing Mix"
menu item:
BACK
BASE
FUNCTION
Q.Link
D/R,EXP
Wing MIX
Touch
Prog.MIX
Aile diff
Flap MIX
Butterfly
Trainer
V-Tail
•
Q.Link-dependent settings
If you have created Quick Links in the submenu
"Q.Link", page 132, and have assigned an ap-
propriate name, it appears at the top right in green
font such as "NORMAL". Activate the corresponding
switches if desired to switch between Quick Links.
•
ACT column
Within the value field for this column, specify whether
the mixer is generally blocked
INH
Once you set this value field to
ON
on and off the mixer with a control assigned in the
right column "CTL".
140
Airplane model function menu - Wing Mix
•
"SET" column
To switch to the setting menu, touch the correspond-
ing
button in the "SET" column with a finger or
>>
000%
the provided stylus.
4.1V
•
Ctrl column
In the value field in the Ctrl column, assign a control
or control switch to the mixer as described in section
"Control, switch and control switch assignment" on
page 38.
RUDD >> AILE line
Frequently, the behaviour of the longitudinal axis is influ-
000
enced when the rudder is actuated. This is particularly
problematic in "knife edge flying" in which the only lift
is from the fuselage when the rudder is deflected since
the wings are vertical in this flight position. This can
SYSTEM
cause a model to rotate as if the aileron were actuated.
A correction is necessary along the longitudinal axis
(aileron) within an adjustable range when the rudders
are controlled.
THR.CRV
Of course, the rudder and aileron remain separately
controllable.
Flap sett
The setting range of ±150 % makes it possible to appro-
priately adapt the direction of deflection. This mixer can
Telemetry
optionally be switched on and off by one of the controls
which cannot be independently reset, or a control switch
if applicable, so that the model can be controlled exclu-
sively using the aileron or rudder.
To set the mixer, use a finger or the provided stylus to
touch the middle button in the line "RUDD >> AILE":
BACK
(active)
MIX.TYPE
RUDD >> AILE
or
.
ON
, you can switch
AILE >> RUDD
RUDD >> ELEV
(control/switch)
(rudder >> aileron)
NORMAL
Graubele
S
ACT
SET
CTL
>>
INH
ON
>
INH
ON
Touch
INH
ON
The corresponding setting menu opens:
NORMAL
BACK
Graubele
RUDD >> AILE
A
(RATE)
+100%
+100%
To enable this, touch the desired value field, such as the
left one, with a finger or the provided stylus:
NORMAL
BACK
Graubele
RUDD >> AILE
A
(RATE)
+100%
+100%
Touch
The color of the field switches from red to blue:
NORMAL
BACK
Graubele
RUDD >> AILE
A
(RATE)
+100%
+100%
Set the desired value with the
or
INC
the right edge.
Use the same procedure for a value on the plus side of
the control travel, for example:
S
B
INC
RES
DEC
S
B
INC
RES
DEC
S
B
INC
RES
DEC
button at
DEC
Advertisement
Table of Contents
