Related Manuals for GRAUPNER Kingpad mc-32 Edition
Summary of Contents for GRAUPNER Kingpad mc-32 Edition
- Page 1 Manual Kingpad mc-32 Edition Bus system control pad for installation in the Graupner mc-32 transmitter No. 3974.32...
- Page 2 2 / 16 3974.32_MP_V1...
-
Page 3: Table Of Contents
Index Introduction ................5 Service Centre ................5 Intended use ................6 Package content ............... 6 Required accessories ............... 6 Technical data ................7 Characteristics ................7 Symbols explication ..............8 Safety notes................8 For your safety by handling the transmitter .........9 Declaration of conformity ............ - Page 4 4 / 16 3974.32_MP_V1...
-
Page 5: Introduction
This manual is part of that product. It contains important informa- tion concerning operation and handling. Keep these instructions for future reference and give it to third person in case you gave the pro- duct. Service centre Graupner Central Service Servicehotline Graupner GmbH (+49) (0)7021/722-130 Henriettenstraße 96... -
Page 6: Intended Use
1 channel of the trans- mitter. The Kingpad mc-32 Edition is designed exclusively to be used in bat- tery-powered, radio controlled models, any other use is not allowed. For any improper use no guarantee or liability is assumed. -
Page 7: Technical Data
Connector type 5 poles XH Note You will find the technical description of the required Kingbus cent- ral module on www.graupner.de directly at the product page (No.3975) Characteristics 11 keys for light control 1 key for level switch ... -
Page 8: Symbols Explication
Symbol description Always observe the information indicated by this warning sign. Par- ticularly those which are additionally marked with the words CAU- TION or WARNING. The signal word WARNING indicates the potential for serious injury, the signal word CAUTION indicates pos- sibility of lighter injuries. -
Page 9: For Your Safety By Handling The Transmitter
For your safety by handling the transmitter WARNING Also while programming the transmitter, make sure that a connec- ted motor cannot accidentally start. Disconnect the fuel supply or drive battery beforehand. 9 / 16 3974.32_MP_V1... -
Page 10: Declaration Of Conformity
WEEE-Reg.-Nr.: DE 42466037 Product description The Kingpad (KP) is made with the SMD technology. With this module, the Graupner / Kingbus lighting system can be controlled. This item has been tested in accordance with EU directives and complies with the legal requirements. -
Page 11: Notes On Environmental Protection
In your own interest please protect the model from dust, dirty and humidity! Warranty certificate The Graupner, Henriettenstrassee 96, 73230 Kirchheim/Teck grants from the date of purchase of this product for a period of 24 months. The warranty applies only to the material or operational defects already existing when you purchased the item. -
Page 12: Installation / Connection
The XH plug has a reverse polarity protection. In the model, this separate channel from the receiver must be connected to the "Kingpad" input on the Graupner central module. Driving and steering channel must continue to remain connected to the central module as well! ... - Page 13 in the transmitter. Now the plugs are plugged into the white XH plug as shown below. The 5 pin XH connector can now be plugged into a free slot. The installation of the hardware is complete. The Kingpad is assigned to a receiver channel via the menu item "Switch assignation"...
-
Page 14: Setting The Kingpad
Setting the Kingpad A co-ordination between the Graupner / Kingpad mc Edition and the Graupner central module must take place so that the perfect function is guaranteed. Proceed as follows: Make sure there is a connection between the remote control and the receiver. -
Page 15: Operation
Operation By pressing a key, the light or the function is switched on, it is swit- ched off by pressing it again. The S key switches between the light level and the function level. Exceptions High beam: not fixed position switch when dipped beam is off. High beam only goes on as long as the button is pressed (flashing light) ...