GRAUPNER S1005 Programming Manual page 76

NORMAL
BACK Graubele
1 7
CH OUT1 CH OUT7
2 8
CH OUT2 CH OUT8
3 9
CH
OUT3 CH OUT9
4 10
CH OUT4 CH OUT10
5 11
CH OUT5 CH OUT11
6 12
CH OUT6 CH OUT12
Repeatedly touch or with a finger or the
INC DEC
provided stylus to select the desired input channel or
transmitter output (see page 96), for example:
NORMAL
BACK Graubele
1 7
CH OUT1 CH OUT7
2 8
CH OUT2 CH OUT8
3 9
CH OUT3 CH OUT9
4 10
CH OUT4 CH OUT10
5 11
CH OUT5 CH OUT11
1 12
CH OUT6 CH OUT12
Touch the button to reset a changed output to the
RES
default mapping.
Use the same procedure to switch other control
channel/receiver output combinations.
NOTE:
If for example you entered "2AILE" in the
basic settings for a model, the transmitter
assigns control function 2 (aileron) to control
channels 2+5 for the left and right aileron. The corres-
ponding transmitter outputs (receiver inputs) to be
mapped would in this case be channels 2+5 (see the
examples below).
All that remains is for your settings to be
transmitted to the receiver since these
settings are only saved in the receiver, and
can only be changed in the "Telemetry" Menu in the
receiver. Touch the [store] button to start
STO
76
Basic menu - Transmitter setting
transmitting, and touch the
SERVO
of the display to return to the "Transmitter setting" menu.
Examples:
• On a large model, you want to control each aileron
INC
flap using two or more servos:
RES
Assign the same input (control channel) to the
DEC
relevant outputs (servo connectors). In this case,
STO assign one of the two default aileron control channels
2 + 5 as an input depending on the left or right wing.
• On a large model, you want to control the rudder
using two or more servos:
Assign the same input (control channel) to the
relevant outputs (servo connectors). In this case,
SERVO
default rudder channel 4.
Note:
• The maximum number of available lines
INC
(outputs) corresponds to the maximum
RES
number of servos that can be connected to
DEC
each receiver.
STO
• You can use the "Output swap" option, page 96,
of the mz-18 HoTT and mz-24 HoTT transmitters to
switch the transmitter control function as desired, or
assign the same control function to several outputs.
For the sake of clarity, it is strongly recommended to
only use one of the two options.
Assigning a channel to two receivers
As mentioned above, you can use the "receiver output"
option to distribute the 9 control channels of the mz-
18 HoTT transmitter, or the 12 control channels of the
mz-24 HoTT transmitter to two receivers as desired.
The numbering of the outputs (servo connectors)
and the maximum number of available lines (outputs)
correspond to the maximum number of servos that can
be connected to the respective receivers. Follow the
same procedure as above.
button at the top left
BACK RF ON/OFF
In this line, you can manually turn the transmitter's RF
transmission off and back on while the transmitter is
currently switched on, for example, to save power while
programming a model.
To manually switch on or off the high-frequency trans-
mission of your transmitter, touch the corresponding
button with a finger or the provide stylus in the "RF ON/
OFF" line:
RF type
The specific RF type needs to be set to satisfy the
relevant guidelines (FCC, ETSI, IC, etc.).
In France for example, originally a remote control
system could only be operated within a restricted
frequency band. With the publication of a new list of
"Class 1 Devices" in July 2012 by the standing EU
Commission and the associated lifting of the permissible
frequency band limit of the relevant subclass 22 from
2.400 to 2.4835 GHz that affects 2.4 GHz remote control
systems, the legal requirements for the earlier "France
mode" are no longer applicable.
The previous France mode can nonetheless still be
used, including outside of France, for example to use
the upper frequency range of the 2.4 GHz band that
this left available for transmitting pictures from an
onboard camera. In this case, however, make sure
that the antenna(s) of the video broadcast system in
The next time the transmitter is switched
on or a model is switched, the OFF setting
is reversed.
BACK Graubele
RX1 RX2
12CH OFF
BIND ON/OFF
SET SET
TX OUT SET
ON NORMAL
RF ON/OFF RF TYPE
O F
RANGE TEST 99sek
Touch
DSC OUTPUT
(country setting)