Thr.crv - GRAUPNER S1005 Programming Manual

THR.CRV

Setting the control characteristic of the Throttle/brake control stick
Note:
This menu is hidden when selecting a model
with "NO POWER" in the basic settings of the
"Model Sel" or "Model type" menu.
In the basic transmitter display, use a finger or the
provided stylus to touch the gear icon labelled "F":
000%
RX TX
RX 00.0V
000:00.0
000 000
mz
000:00.0
0:01:23
Touch
M 1
000 000
NORMAL
Graubele
BATT TIME 00: 01: 23
000
The display switches to the blue function menu. Use a
finger or the provided stylus to touch the "THR.CRV"
menu item:
BACK BASE FUNCTION
Q.Link D/R,EXP Wing MIX
Prog.MIX Aile diff Flap MIX
Butterfly Trainer V-Tail
In this menu, you can adapt the carburettor
characteristic as well as the idle LOW and "motor off"
position of the throttle.
This menu allows you to change the control character-
istic of the throttle control stick independent of whether
the control function acts directly on a servo connected
to control channel 1, or via a number of mixers on
several servos.
144
Airplane model function menu - THR.CRV
Q.Link-dependent settings
If Quick Links are specified in the "Q.Link" menu,
page 132, this option can be adopted depending on
the Quick Link. The name of the Quick Link is displayed
in green at the top right of the display, such as "NOR-
MAL".
First switch to the desired Quick Link, if desired.
000%
Changing the control direction
4.1V
In the wing program of the mz-18 HoTT and mz-24
HoTT transmitters, the rear throttle position is the
default for the "motor off" position with electric drives,
and "idle LOW" for gas motors. By inverting the throttle
curve, the control direction of the throttle can be
changed as needed from "accelerate from back to front"
to "accelerate from front to back".
000 Switch on the graphic and numerical display of the
control stick position by touching the
at the bottom left of the display with a finger or the
provided stylus, and then activate the Y-coordinate
adjustment option by touching the
SYSTEM
BACK
THR.CRV
Touch
p
Telemetry
Use the throttle to move a vertical green line between
the two endpoints "L" and "H" in the graphic. The mo-
mentary control stick position is also displayed numeri-
cally in the line "IN" (-100 % to +100 %).
Then move the throttle to one of the two end positions
such as the front. The green line moves the right and
disappears under the white frame. At the same time, the
color of the point at the top right changes from green to
red:
button
ST OFF
button:
Y-axis
Graubele NORMAL S
CURVE OFF
IN –100% INC
OUT –100%
POINT L 000% DEC
ST ON X-axis Y-axis ENT
NORMAL
BACK Graubele
CURVE OFF
IN +100%
OUT +100%
POINT H +100%
ST ON X-axis Y-axis
Hold down the button at the right edge of the
DEC
display with a finger or the provided stylus to move the
red point down to a value of 000% in the line "POINT":
NORMAL
BACK Graubele
CURVE OFF
IN +100%
OUT –100%
POINT H
000%
ST ON X-axis Y-axis
Then move the throttle to the opposite end position,
such as the rear. The green line moves to the left, and
the points at the ends of the yellow horizontal line
change color:
NORMAL
BACK Graubele
CURVE OFF
IN –100%
OUT –100%
POINT L 000%
ST ON X-axis Y-axis
Use a finger or the provided stylus to hold down
the button at the right side of the display until a
INC
value of +100% is reached in the "POINT" line.
S
INC
DEC
ENT
S
INC
DEC
ENT
S
INC
DEC
ENT