Sub-Trim - GRAUPNER S1005 Programming Manual

Sub-Trim

Setting the neutral position of servos
In the basic transmitter display, use a finger or the
provided stylus to touch the gear icon labelled "B":
000%
RX TX
RX 00.0V
000:00.0
000 000
mz
000:00.0
0:01:23
Touch
M 1
000 0
NORMAL
Graubele
BATT TIME 00: 01: 23
000
The display switches to the green base menu. Touch
the menu item "Sub-Trim" with a finger or the provided
stylus.
BACK BASE FUNCTION
Model Sel Model Type E.P.A Rev/Slow
TX ctl Fail Safe
Motor Timer
Servo CH Set Out.Swap
Sub-Trim
The servo middle position is for adapting servos that are
not standard (servo middle position with a pulse length
of 1.5 ms or 1500 μs ) as well as for minor adaptations,
for example fine adjustment to the neutral position of the
control surfaces on the model.
Independent of trim levers and any mix settings, the
neutral position can be shifted around ±125% within the
maximum servo travel of ±150%. The servo is always
adjusted directly independent of all other trim and mix
settings.
70
Basic menu - Sub-Trim
Note that if the neutral position is adjusted
strongly, servo travel on one side may be
restricted since the total travel is limited to
000%
±150% for electronic and mechanical reasons.
4.1V
BACK
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
000
CH 6.
Note:
SYSTEM
•
Move the trim lever into the middle position
before changing the middle values.
In contrast to the display of the 12-channel mz-
•
Sub-Trim
24 HoTT transmitter in this section, only channels
1 ... 9 are offered in the display of the 9-channel mz-
Touch
Trim Step
18 HoTT transmitter.
To change the neutral position of a specific servo, touch
the corresponding button, for example:
BACK
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
The button color changes from red to blue:
Graubele SERVO
000% CH 7. 000%
000% CH 8. 000%
000% CH 9. 000% INC
000% CH 10. 000% RES
000% CH 11. 000% DEC
000% CH 12. 000%
Graubele SERVO
000% CH 7. 000%
000% CH 8. 000%
000% CH 9. 000% INC
0 % CH 10. 000% RES
Touch
CH 11. 000% DEC
000% CH 12. 000%
BACK Graubele
CH 1. 000% CH 7. 000%
CH 2. 000% CH 8. 000%
CH 3. 000% CH 9. 000%
CH 4. 000% CH 10. 000%
CH 5. 000% CH 11. 000%
CH 6. 000% CH 12. 000%
Change the value by touching or
INC
right to the outside, for example:
BACK Graubele
CH 1. 000% CH 7. 000%
CH 2. 000% CH 8. 000%
CH 3. +012% CH 9. 000%
000% CH 10. 000%
CH 4.
CH 5. 000% CH 11. 000%
CH 6. 000% CH 12. 000%
Touch the button to reset a changed value in the
RES
blue field back to the default.
Touch the button in the top right of the display
SERVO
to open the graphic display of the servo travel and
positions described in greater detail on page 90 and
activate (if desired) the "Servo test" function integrated
in this display:
To go to the "Home menu", leave the "Sub-Trim" display
by touching the button at the top left:
BACK
BACK Graubele
CH 1. 000% CH 7. 000%
Touch
CH 2. 000% CH 8. 000%
CH 3. +012% CH 9. 000%
CH 4. 000% CH 10. 000%
CH 5. 000% CH 11. 000%
CH 6. 000% CH 12. 000%
SERVO
INC
RES
DEC
on the
DEC
SERVO
INC
RES
DEC
SERVO
INC
RES
DEC