Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 81

E Detailed Occurance Items
code code area
E025 -0300 -05 Title Toner bottle motor lock (C) error
Description Overcurrent of the toner container drive motor was
of detection detected.
Measures 1. Check whether a toner container of a different model is
not installed.
If it is installed, replace it with a correct one.
2. Check the connection of the toner container drive
motor (M7/M10/M13/M16). (Check whether the wire is
not caught by parts.)
3. Replace the toner container drive motor.
4. Replace the toner container tray unit (when this error
occurred at rotation of the toner container).
5. Replace the hopper unit.
E025 -0302 -05 Title Block supply timeout (C) error
Description The toner supply screw rotation sensor cannot detect
of detection rotation of the screw.
Measures 1. Check the connection between the hopper/stirring
supply motor (M15) and the hopper driver PCB.
Motor side: J7102, J8108 PCB side: J1350
2. Check the connection between the toner feed screw
rotation sensor (PS18) and the hopper driver PCB.
Sensor side: J7420, J8108 PCB side: J1350
3. Replace the hopper/stirring supply motor.
4. Clean and replace the toner feed screw rotation
sensor.
5. Replace the toner supply pipe unit.
6. Replace the hopper unit.
CAUTION:
Remedies 5 and 6 are taken when the motor is
overloaded due to toner adhesion in the unit or gear
interlocking failure, etc. Since it is difficult to identify the
cause, it is recommended to replace the unit.
Description
1-1. Open the toner container installation inlet
cover.
1-2. Manually turn the container in an
counterclockwise direction until it is fully turned.
1-3. Rotate the toner container in an
counterclockwise direction using a toner
container removing tool.
1-4. The toner container is placed at the position
where it can be removed. Remove the toner
container.
E Detailed Occurance Items
code code area
E025 -0310 -05 Title Toner container sealing/release holder shift cam HP
sensor timeout (C) error
Description HP sensor of release holder shift cam cannot detect
of detection within specified period of time.
Measures 1. Check the connection of the toner container drive
2. Check the connection between the release holder shift
3. Replace the toner container drive motor.
4. Clean and replace the release holder shift cam HP
5. Replace the hopper unit.
CAUTION:
As for Remedy 5, since it is difficult to identify the cause,
it is recommended to replace the unit.
NOTE: After performing the above remedy work, go
through the following to clear the error: COPIER>
FUNCTION> CLEAR> ERR
E025 -0320 -05 Title Toner container/toner container inserting inlet phase (C)
error
Description When the power was turned on, it was detected that the
of detection toner container cap was opened (the release holder shift
cam phase sensor was protected against light) AND the
toner container inserting inlet cover was opened (the
toner container inserting inlet cover open/close sensor
was transmissive).
Measures 1. Close the toner container inserting inlet cover and turn
2. Check the connection between the toner container
3. Check the connection between the release holder shift
4. Replace the toner container inserting inlet cover open/
Description
motor (M16) harness. (Check whether the wire is
not caught by parts.) Check the connection with the
hopper driver PCB.
Motor side: J7106 PCB side: J1370
cam HP sensor (PS17) and the hopper driver PCB.
Sensor side: J7129, J8108 PCB side: J1350
sensor.
OFF/ON the power.
inserting inlet cover open/close sensor (PS16) and
the hopper driver PCB. (Connection of the connector,
Shorting, Wire caught by parts)
Sensor side: J7128, J8115 PCB side: J1360
cam phase sensor (PS82) and the hopper driver PCB.
(Connection of the connector, Shorting, Wire caught by
parts)
Sensor side: J7150 PCB side: J1390
close sensor.
3
3-55