Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 676

TEST
■ PG
TYPE Test print
Lv.1 Details To execute the test print.
Use case At trouble analysis
Adj/set/operate method Enter the setting value, and then press Start key.
Test print is executed.
Caution Be sure to return the value to 0 after the test print output.
Display/adj/set range 0 to 100
0: Image from CCD (normal print)
1 to 3: For R&D use
4: 16 gradations
5: Halftone for all areas
6: Grid
7 to 9: For R&D use
10: MCYBk horizontal (side) line
11: For R&D use
12: YMCBk 64 gradations
13: For R&D use
14: Full color 16 gradations
15 to 54: For R&D use
55: PG for REOS
56 to 100: For R&D use
Default value 0
TXPH Setting of test print image mode
5
Lv.1 Details To set the image mode at the time of test print output.
This mode is enabled for test print only.
Use case At trouble analysis
Display/adj/set range 0 to 6
0: Error diffusion
1: Low screen ruling screen (approx. 133 to 190 lines)
2: High screen ruling screen (approx. 200 to 268 lines)
3: Copy screen (approx. 220 lines)
4: REOS screen (no screen structure)
5: Error diffusion (with end correction)
6: High-line-count screen (with end correction)
THRU Image correction table use at test print
Lv.1 Details To set whether to use the image correction table at the time of test
print output.
Use case At trouble analysis
Display/adj/set range 0 to 1
0: Used, 1: Not used
Default value 0
5-448
COPIER> TEST> PG
COPIER> TEST> PG
DENS-Y Adj of Y color density at test print
Lv.1 Details To adjust Y color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Display/adj/set range 0 to 255
DENS-M Adj of M color density at test print
Lv.1 Details To adjust M color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Display/adj/set range 0 to 255
DENS-C Adj of C color density at test print
Lv.1 Details To adjust C color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Display/adj/set range 0 to 255
DENS-K Adj of Bk color density at test print
Lv.1 Details To adjust Bk color density when performing test print (TYPE=5).
As the value is increased, the density becomes higher.
Use case At test print (TYPE=5)
Display/adj/set range 0 to 255
COLOR-Y Y color output setting at test print
Lv.1 Details To make a setting of Y color output for test print.
The setting is applied to all types.
When setting "COLOR-Y" to 1 and other items to "0", a single Y color
is output.
Use case At test print
Display/adj/set range 0 to 1
0: Not output, 1: Output
COLOR-M M color output setting at test print
Lv.1 Details To make a setting of M color output for test print.
The setting is applied to all types.
When setting "COLOR-M" to 1 and other items to "0", a single M
color is output.
Use case At test print
Display/adj/set range 0 to 1
0: Not output, 1: Output
COLOR-C C color output setting at test print
Lv.1 Details To make a setting of C color output for test print.
The setting is applied to all types.
When setting "COLOR-C" to 1 and other items to "0", a single C color
is output.
Use case At test print
Display/adj/set range 0 to 1
0: Not output, 1: Output