Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 410

Addres bit Description
P010 7 DIPSW1-8 on the finisher controller
PCB
6 DIPSW1-7 on the finisher controller
PCB
5 DIPSW1-6 on the finisher controller
PCB
4 DIPSW1-5 on the finisher controller
PCB
3 DIPSW1-4 on the finisher controller
PCB
2 DIPSW1-3 on the finisher controller
PCB
1 DIPSW1-2 on the finisher controller
PCB
0 DIPSW1-1 on the finisher controller
PCB
P011 7 EEPROM clock signal
6 EEPROM enable signal
5 EEPROM output signal
4 not used
3 gear change motor electric current
change I1
2 gear change motor electric current
change I0
1 gear change motor phase B signal
0 gear change motor phase A signal
P012 7 swing height sensor
5
6 gear change home position sensor
5 not used
4 rear end assist HP sensor
3 processing tray sensor
2 rear aligning plate HP sensor
1 front aligning plate HP sensor
0 EEPROM input signal
P013 7 tray 2 shift motor ON signal
6 tray 2 shift motor CW/CCW signal
5 feed roller separation solenoid
4 punch feed motor standby
3 punch feed motor electric current
change I0
2 punch feed motor electric current
change I1
1 feed motor electric current change
I0
0 feed motor electric current change
I1
5-182
Symbol Remarks
- 0:ON/1:OFF
- 0:ON/1:OFF
- 0:ON/1:OFF
- 0:ON/1:OFF
- 0:ON/1:OFF
- 0:ON/1:OFF
- 0:ON/1:OFF
- 0:ON/1:OFF
- -
- 0:OFF/1:ON
- 0:OFF/1:ON
- -
M110 -
M110 -
M110 -
M110 -
PI123 0:close/1:open
PI117 0:HP/1:besides HP
- -
PI109 0:HP/1:besides HP
PI108 0:paper present/1:paper absent
PI107 0:HP/1:besides HP
PI106 0:HP/1:besides HP
- -
M108 0:OFF/1:ON
M108 0:CW/1:CCW
SL101 0:OFF/1:ON
M63 0:standby/1:drive
M63 -
M63 -
M101 -
M101 -
Addres bit Description
P014 7 tray 1 shift motor enable signal
6 tray 1 shift motor CW/CCW signal
5 tray 1 shift motor ON signal
4 rear end assist motor enable signal
3 rear end assist motor electric
current change I1
2 rear end assist motor electric
current change I0
1 rear end assist motor directiojn
change
0 inserter serial communication
(OUT)
P015 7 staple motor direction change CW
signal
6 staple motor direction change
CCW signal
5 Stapler shift motor enable signal
4 stack ejection motor electric current
change I0
3 stack ejection motor electric current
change I1
2 stack ejection motor torque
terminal
1 swing motor electric current
change
0 swing motor direction change
P016 7 not used
6 rear aligning plate motor direction
change
5 rear aligning plate motor clock
signal
4 rear aligning plate motor electric
current change I0
3 not used
2 front aligning plate motor electric
current change I0
1 front aligning plate motor direction
change
0 front aligning plate motor clock
signal
Symbol Remarks
M107 0:standby/1:drive
M107 0:CW/1:CCW
M107 0:OFF/1:ON
M109 0:standby/1:drive
M109 -
M109 -
M109 0:CW/1:CCW
- 0:OFF/1:ON
M41 -
M41 -
M105 0:drive/1:standby
M102 -
M102 -
M102 0:71%/1:100%
M106 0:High/1:Low
M106 0:CW/1:CCW
- -
M104 0:CW/1:CCW
M104 -
M104 0:High/1:Low
- -
M103 0:High/1:Low
M103 0:CW/1:CCW
M103 -