Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 555

COPIER> OPTION> FNC-SW
INTROT-2 Set of last rotation auto adj exe intvl
Lv.1 Details To set the paper interval to execute auto adjustment (D-max control,
D-half control) at last rotation.
As the value is incremented by 1, the paper interval is increased by 1
sheet. When 0 is specified, the control is not executed.
Use case When matching the use environment of the user.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Increasing the number of sheets (widening the interval) causes
higher frequency of image failure.
Display/adj/set range 0 to 20000
0: No control
Unit 1 sheet
Default value 15000
Related service mode COPIER> OPTION> CLEANING> W-CLN-P
INTROT-T Clr displace crrct:horz scan after start
Lv.1 Details Color displacement may occur right after starting a job (1 to 5 sheets)
due to the ITB Unit specific variation.
When the setting value is changed, write start position of each color
is adjusted according to the color displacement correction level only
right after starting a job (1 to 5 sheets), so color displacement can be
corrected.
Use case When color displacement in the horizontal scanning direction occurs
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use the setting value 4 to 10. Use 0 to 3 in the normal
operation.
Display/adj/set range 0 to 10
0: Color displacement correction level 0
1: Color displacement correction level 1
2: Color displacement correction level 2
3: Color displacement correction level 3
4 to 10: Not used
Default value 3
COPIER> OPTION> FNC-SW
MODELSZ2 Ppr size dtct global support in bookmode
Lv.2 Details To set ON/OFF for global support of document size detection in
copyboard reading mode.
Use case Upon user's request (mixed media original with AB/Inch
configuration)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution • Do not use this at the normal service.
• The Document Size Sensor (Photo Sensor) is additionally required
to correctly detect the document size when the original consists of
mixed media (AB/Inch configuration).
Display/adj/set range 0 to 1
0: Detected with detection size according to location, 1: Detected
with AB/Inch mixed media.
Default value 0
SVMD-ENT Setting of entry method to service mode
Lv.2 Details To set the way to get in service mode to prevent information leak.
Use case As needed
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: [Settings/Registration] - Pressing [2] and [8] at the same time -
[Settings/Registration]
1: [Settings/Registration] - Pressing [4] and [9] at the same time -
[Settings/Registration]
Default value 0
FXWRNLVL Set No.of fed sht FxBltUnt warn dis lvl
Lv.2 Details To set the threshold value for the number of fed sheets to display the
life alarm message of Fixing Belt Unit.
Use case When switching the warning level of the Fixing Belt Unit
Display/adj/set range 0 to 3
0: Error display threshold value
1: The value 10,000 smaller than the error display threshold value
2: The value 20,000 smaller than the error display threshold value
3: The value 30,000 smaller than the error display threshold value
Default value 1
Related service mode COPIER> OPTION> IMG-FIX> FX-U-ERR
COPIER> OPTION> DSPLY-SW> FXMSGSW2
5
5-327