Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 742

TRM-RG2 Skew adj (large size): Bklt
Lv.1 Details To adjust the skew of paper stack larger than A4 size on Finisher
Trimmer.
As the value is incremented by 1, the paper stack stop position
moves by 0.1mm.
+: Toward delivery direction
-: Toward inlet direction
Use case When the skew occurs on paper stack larger than A4 size
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
TRM-CUT1 Trimming position adj (small size): Bklt
Lv.1 Details To adjust the trimming position of A4 size or smaller paper stack on
Finisher Trimmer.
As the value is incremented by 1, the paper stack stop position
moves by 0.1mm.
+: Toward delivery direction
-: Toward inlet direction
Use case When the trimming position is displaced on A4 or smaller paper stack
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
TRM-CUT2 Trimming position adj (large size): Bklt
5
Lv.1 Details To adjust the trimming position of the paper stack larger than A4 size
on Finisher Trimmer.
As the value is incremented by 1, the paper stack stop position
moves by 0.1mm.
+: Toward delivery direction
-: Toward inlet direction
Use case When the trimming position is displaced on the paper stack larger
than A4 size
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
5-514
SORTER> ADJUST SORTER> ADJUST
BFF-SFT2 Paper displace amount on buffer: Bklt
Lv.1 Details To adjust the paper displacement amount on Finisher Buffer
Assembly.
As the value is incremented by 1, the paper position moves by 0.1mm.
+:
-:
Use case When the paper displacement occurs on the 2nd to 3rd sheets of the
2nd sets (B5/A4/LTR) and later
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
SDL-STP Adj of Saddle Stitcher staple position
Lv.1 Details To adjust the staple position of Saddle Stitcher.
As the value is incremented by 1, the staple position moves by mm.
+:
-:
Use case When the staple position of the Saddle Stitcher is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-FLD Adj of Saddle Stitcher fold position
Lv.1 Details To adjust the fold position of Saddle Stitcher.
As the value is incremented by 1, the fold position moves by mm.
+:
-:
Use case When the fold position of the Saddle Stitcher is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0