Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 510

COPIER> FUNCTION> INSTALL
INISET-C Exe of C Dev Ass'y initial install mode
Lv.1 Details To automatically execute operation necessary for initial installation of
the C Developing Assembly.
1. Patch light intensity correction
2. Background correction
3. Potential control
4. Idle rotation of the Developing Assembly
5. Initialization of the Toner Density Sensor
6. Initialization of the Patch Sensor
7. Counter reset of the Developing Assembly
After execution, the AINR-OFF setting automatically returns to "0:
OFF".
Use case When replacing the C Developing Assembly
Adj/set/operate method Select the item, and then press OK key.
Caution • When installing the machine or replacing the Developing Assembly
of other color, do not use this item. .
• Execute this item after setting "AINR-OFF" to "1: ON".
Display/adj/set range During operation: xxx second (remaining time), At normal termination:
OK, At abnormal termination: NG
Required time 155 seconds
Related service mode COPIER> FUNCTION> INSTALL> INISET-Y, INISET-M, INISET-K,
INISET-4, AINR-OFF
AINR-OFF ON/OFF of warm-up rotation deactivation
Lv.1 Details To set ON/OFF to disable execution of warm-up rotation.
Warm-up rotation can be omitted when turning OFF/ON the power to
check the image, etc. after the adjustment of warm-up rotation, etc.
This mode is executed when warm-up rotation is not needed.
5
Use case • At installation
• When replacing the Developing Assembly
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to enable the operation (cancel disabling) before the
machine is used by the user. The operation is automatically enabled
by executing INISET-Y/M/C/K/4.
Display/adj/set range 0: OFF (warm-up rotation enabled), 1: ON (warm-up rotation
disabled)
Default value 0
Related service mode COPIER> FUNCTION> INSTALL> INISET-Y, INISET-M, INISET-C,
INISET-K, INISET-4
5-282
COPIER> FUNCTION> INSTALL
E-RDS Set use/no use of Embedded-RDS function
Lv.1 Details To set whether to use the Embedded-RDS function.
Use case When using Embedded-RDS
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range 0: Function not used, 1: Function used (All the counter information is
sent.)
Default value 0
Related service mode COPIER> FUNCTION> INSTALL> RGW-PORT, COM-TEST, COM-
LOG, RGW-ADR
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
RGW-PORT Set port number of Sales Co's server
Lv.1 Details To set the port number of the sales company's server to be used for
Embedded-RDS.
Use case When using Embedded-RDS
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range 1 to 65535
Default value 443
Related service mode COPIER> FUNCTION> INSTALL> E-RDS, COM-TEST, COM-LOG,
RGW-ADR
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
COM-TEST Disp connect result w/ Sales Co's server
Lv.1 Details To display the result of the connection test with the sales company's
server.
Use case When using Embedded-RDS
Adj/set/operate method Select the item, and then press OK key.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range During operation: ACTIVE, When connection is completed: OK,
When connection is failed: NG
Related service mode COPIER> FUNCTION> INSTALL> E-RDS, RGW-PORT, COM-LOG,
RGW-ADR
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol