Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 561

COPIER> OPTION> FNC-SW
JLK-PWSC ON/OFF of PCAM password auth doc scan
Lv.2 Details To set whether to scan the PCAM password authentication document
with the MEAP application.
Use case When scanning the PCAM password authentication document
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
ATUDILOG ON/OFF of UDI log record
Lv.2 Details To set ON/OFF of UDI log record mode.
UDI log file is normally written in HDD file, but it is deleted at start-up
so the UDI log is not recorded.
When 1 is set, UDI log is recorded in HDD at job assignment, and is
written out with sub log when obtaining it with USB memory (it can
be also obtained from SST).
Use case When investigation is not possible with only sub log at the time of
trouble occurrence
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to get approval from the user by telling that third party other
than Canon cannot recover the original document and image from
UDI log.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
FAX-INT Set FAX RX print interruption oprtn mode
Lv.2 Details To set the mode performing interruption operation of FAX reception
print automatically.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal, 1: Interruption operation mode
Default value 0
COPIER> OPTION> FNC-SW
PDL-Z-LG Setting of draw algorithm
Lv.1 Details To switch the draw algorithm of the iR C Series and the iR-ADV C
Series to obtain output the user expects.
When 0 (FURUYA mode) is set, image is output as displayed on the
screen by the new algorithm adopted from the iR-ADV C Series.
Pseudo outline (boundary for processing divided graphics separately)
occurred with the iR C Series does not occur. However, when PDL
job with special data structure is sent, output the user expects may
not be obtained.
When 1 (FLAG mode) is set, the draw algorithm adopted by the
conventional iR C Series is used. Output equivalent to that of the
iR C Series can be obtained; however, draw-related phenomenon
occurred with the series occurs.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use setting value 2 and 3.
Display/adj/set range 0 to 3
0: FURUYA mode, 1: FLAG mode, 2,3: For R&D use
Default value 0
CDS-LVUP Set to allow CDS periodical update
Lv.1 Details To set whether to permit periodical update by CDS.
When 0 is set, the user administrator/service technician can set the
periodical update function from the user mode/service mode. With
this setting, Updater performs periodical update.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 1
0: Disabled, 1: Enabled
Default value The value differs according to the location.
Supplement/memo CDS: Contents Delivery System
UA-OFFSW ON/OFF of unified auth function
Lv.1 Details To set ON/OFF of the Unified Authentication function.
Set 0 when not preferring to use the Unified Authentication function
because of security concern.
Use case Upon user's request (not to use the Unified Authentication function)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
5
5-333