Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 625

COPIER> OPTION> USER
IFAX-OF IFAX send prohibition to entered address
Lv.1 Details To set to prohibit address entry at the time of I-Fax transmission.
IFAX transmission is not available by entering the address because
of no display of "I-Fax" on the transmission screen.
The addresses already registered in the Address Book can be used.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution To restrict addresses for transmission, be sure to manually delete
them because the addresses registered in the Address Book can be
used.
Display/adj/set range 0 to 1
0: Enabled, 1: Disabled
Default value 0
LDAP-DEF Initial condtn set of LDAP server search
Lv.1 Details To set initial condition for search target attribute that is specified at
the time of LDAP server Details search.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 6
0: Name, 1: E-mail, 2: FAX, 3: Organization, 4: Organization unit, 5:
No registration 1 (any setting), 6: No registration 2 (any setting)
Default value 0
Related service mode COPIER > OPTION > USER > LDAP-SW
JA-DPI Dis of job archive record resolution
Lv.2 Details To display the resolution of images for job archives recorded in jobs
other than FAX reception and IFAX reception, etc.
Only display is available in service mode. The setting is available
only in the MEAP applications which support job archiving.
Use case Upon user's request
Display/adj/set range 0 to 3
0: No conversion, 1: 100 x 100 dpi, 2: 200 x 200 dpi, 3: 300 x 300 dpi
Default value 3
JA-COMPR Dis of job archive record compress ratio
Lv.2 Details To display the compression ratio of images for job archives recorded
in jobs other than FAX reception and I-Fax reception, etc.
Only display is available in service mode. The setting is available
only in the MEAP applications which support job archiving.
Use case Upon user's request
Display/adj/set range 0 to 5
0: No conversion, 1: Compression ratio 1/4, 2: Compression ratio
1/8, 3: Compression ratio 1/16, 4: Compression ratio 1/32, 5:
Compression ratio 1/64
Default value 3
COPIER> OPTION> USER
DK3-ASST Set of M-Deck(Middle) Air Heater control
Lv.1 Details To set the condition to turn on the Air Heater at the Multi Deck (Middle)
in accordance with media/environment.
When the media is switched from non-coated paper to coated paper,
pickup operation does not start until the temperature of the Air
Heater reaches the specified temperature; thus, waiting time occurs.
By selecting 1, the Air Heater is ON only for the coated paper.
When the use environment is near the threshold for turning ON/OFF
the Air Heater, switching occurs frequently, which increases the wait
time. By selecting 2, the heater is always ON regardless of media
and environment.
Use case Upon user's request (shorten the wait time)
Caution When selecting 2, be sure to receive approval from the user in
advance after explaining that there is a possibility that transfer
performance may decrease if humidity decreases.
Display/adj/set range 0 to 2
0: ON/OFF depending on the media/environment condition
1: ON only for the coated paper
2: Always ON (No environment/media-dependant)
Default value 0
FREE-DSP Display/hide of charge disable screen
Lv.2 Details To set whether to display or hide the Use Charge Management
screen for switching between charge and no charge.
The hardware switch for switching charge/no charge in the Coin
Manager enables the mode in which all the services are available
for free (store manager mode) by temporarily releasing the charging
system.
Even without the hardware switch, the mode can be switched
with the software switch when it is set to display the Use Charge
Management screen in Settings/Registration.
Use case When enabling all the services to be provided for free by temporarily
releasing the charging system
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
Related user mode Management Settings > Charge Management > Use Charge
Management
5
5-397