Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 596

COPIER> OPTION> NETWORK
NS-LGN Limit LOGIN authentication at SMTP auth
Lv.2 Details To restrict use of LOGIN authentication at the time of SMTP
authentication.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: SMTP server-dependent, 1: Not used
Default value 0
Supplement/memo SMTP authentication: Protocol in which user authentication
function is added to SMTP, which is the protocol to be used
for e-mail transmission. At the time of e-mail transmission, this
protocol executes authentication of the user account and the
password between the SMTP server and the user to approve e-mail
transmission only when it's authenticated.
MEAP-PN HTTP port No.setting of MEAP application
Lv.2 Details To set HTTP port number of MEAP application.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not specify port 8080 when the Print Server is connected.
Otherwise, you cannot browse the device RUI in which MEAP
authentication application is running (Port 8080 is reserved for
redirection of EFI controller to the iR side.)
Display/adj/set range 0 to 65535
Default value 8000
DA-PORT Port setting with DA
5
Lv.2 Details To set the communication port when DA is installed.
Select ON when DA is installed.
Use case When DA is installed (This mode is used for the Japanese models
only and not used with overseas models (outside Japan)).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When going through the following: COPIER > OPTION > FNC-SW
> DA-CNCT, and selecting 1 for DA-CNCT, the following item is also
ON:
COPIER > OPTION > NETWORK > STS-PORT, CMD-PORT
COPIER > OPTION > FNC-SW > DA-PORT
Display/adj/set range 0 to 1
0: OFF, 1: ON (When installed)
Default value 0
Supplement/memo DA: Digital Accessory
5-368
COPIER> OPTION> NETWORK
DA-CNCT Connection setting of WPGW
Lv.2 Details To set WPGW connection.
Use case This mode is used for the Japanese models only and not used with
overseas models (outside Japan)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Go through the following: COPIER > OPTION > ACC > COIN; and
if the setting value for COIN is changed from 0/1/2 to 3 (select DA
charge), the value is automatically turns 1.
Display/adj/set range 0 to 1
0: OFF, 1:ON
Default value 0
Related service mode COPIER> OPTION> ACC> COIN
Supplement/memo WPGW: Workplace Gateway
CHNG-STS Set of TOT status connection port number
Lv.2 Details To set the port number for status connection with T.O.T.
Use case When the Service NAVI is used
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 65535
Default value 20010
Related service mode COPIER> OPTION> NETWORK> STS-PORT
CHNG-CMD Set of TOT command connection port No.
Lv.2 Details To set the port number for command connection with T.O.T.
Use case When the Service NAVI is used
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 65535
Default value 20000
Related service mode COPIER> OPTION> NETWORK> CMD-PORT
MEAP-SSL HTTPS port setting of MEAP
Lv.2 Details To set the port of HTTPS server in the case of using SSL with HTTP
of MEAP.
Use case When specifying the setting of HTTPS port for MEAP
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
Default value 8443