Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 597

COPIER> OPTION> NETWORK
LPD-PORT Setting of LPD port number
Lv.2 Details To set the LPD port number.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 65535
Default value 515
Supplement/memo LPD port: Network port for TCP/IP communication when making
prints through network.
WUEV-SW Setting of sleep notification execution
Lv.2 Details To set whether to notify the sleep mode to the application
(imageWARE, etc) on the network when shifting to/recovering from
the sleep mode.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Notified, 1: Not notified
Default value 0
WUEV-INT Setting of sleep notification interval
Lv.2 Details To set the interval of sleep notification.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This is active when COPIER> OPTION> NETWORK> WUEV-SW is
set to 0: Notified.
Display/adj/set range 60 to 65535
Unit 1 second
Default value 600
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEV-POT Port number setting for sleep notice
Lv.2 Details To set port number of the PC to notify the sleep mode.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This is active when COPIER> OPTION> NETWORK> WUEV-SW is
set to 0: Notified.
Display/adj/set range 1 to 65535
Default value 11427
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
COPIER> OPTION> NETWORK
WUEV-RTR Setting of sleep notification range
Lv.2 Details To set the number of available routers to the target for sleep
notification.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This is active when COPIER> OPTION> NETWORK> WUEV-SW is
set to 0: Notified.
Display/adj/set range 0 to 254
Default value 3
Related service mode COPIER> OPTION> NETWORK> WUEV-SW
WUEN-LIV Recovery time setting after sleep notice
Lv.2 Details To set the time from the sleep start from network without job
assignment until the mode is shifted to the sleep mode.
Use case When setting the startup time after sleep notification
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 600
Unit 1 second
Default value 15
DHCP-12 ON/OFF of DHCP-option 12 request
Lv.2 Details To set ON/OFF of inquiry on the host name (Option 12) which uses
Option 55 of DHCP.
Selecting OFF can prevent DHCP packet from including Option 12 or
Option 81 under the packet-monitoring network environment.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo DHCP: Dynamic Host Configuration Protocol
5
5-369