Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 462

COPIER> ADJUST> HV-TR
TR-ENV8 Sec trns indiv setting environment:set 8
Lv.2 Details To set the environment (absolute moisture amount) for setting 8.
Setting 8 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV8,
TR-PPR8, TR-CLR8 and TR-DUP8. When this condition is satisfied,
the target current that is set in 2TR-TGT8 and paper allotted voltage
that is set in 2TR-SHR8 are applied to the Secondary Transfer Outer
Roller.
Use case When an image failure that differs due to the environment occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: Low humidity (Absolute moisture amount: 5.8g/m3 and less)
2: Normal humidity (5.9 to 15g/m3)
3: High humidity (15.1g/m3 and more)
Default value 2
Related service mode COPIER> ADJUST> HV-TR> TR-PPR8, TR-CLR8, TR-DUP8, 2TR-
TGT8, 2TR-SHR8
TR-CLR1 Sec trns indiv setting color mode: set 1
Lv.2 Details To set B&W/color for setting 1.
Setting 1 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV1,
TR-PPR1, TR-CLR1 and TR-DUP1. When this condition is satisfied,
the target current that is set in 2TR-TGT1 and paper allotted voltage
that is set in 2TR-SHR1 are applied to the Secondary Transfer Outer
Roller.
5
Use case When an image failure that differs due to the color mode occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 2
1: B&W mode, 2: Color mode
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV1, TR-PPR1, TR-DUP1, 2TR-
TGT1, 2TR-SHR1
5-234
COPIER> ADJUST> HV-TR
TR-CLR2 Sec trns indiv setting color mode: set 2
Lv.2 Details To set B&W/color for setting 2.
Setting 2 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV2,
TR-PPR2, TR-CLR2 and TR-DUP2. When this condition is satisfied,
the target current that is set in 2TR-TGT2 and paper allotted voltage
that is set in 2TR-SHR2 are applied to the Secondary Transfer Outer
Roller.
Use case When an image failure that differs due to the color mode occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 2
1: B&W mode, 2: Color mode
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV2, TR-PPR2, TR-DUP2, 2TR-
TGT2, 2TR-SHR2
TR-CLR3 Sec trns indiv setting color mode: set 3
Lv.2 Details To set B&W/color for setting 3.
Setting 3 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV3,
TR-PPR3, TR-CLR3 and TR-DUP3. When this condition is satisfied,
the target current that is set in 2TR-TGT3 and paper allotted voltage
that is set in 2TR-SHR3 are applied to the Secondary Transfer Outer
Roller.
Use case When an image failure that differs due to the color mode occurs
(mottled image/density loss due to excessive transfer/toner scattering
on solid image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 2
1: B&W mode, 2: Color mode
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV3, TR-PPR3, TR-DUP3, 2TR-
TGT3, 2TR-SHR3