Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 524

COPIER> FUNCTION> CLEAR
MMI Clear of user mode setting value
Lv.1 Details To clear the user mode setting values (excluding values for Control
Panel, common settings, and FAX).
• Common Settings
• Timer Settings
• Adjustment/Cleaning
• Report Settings
• System Settings
• Copy Settings
• Communications Settings
• Printer Settings
Use case When clearing various setting values of user mode
Adj/set/operate method 1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The setting value is cleared after the main power switch is turned
OFF/ON.
MN-CON RAM clear of MNCON PCB SRAM Board
Lv.1 Details To clear the RAM data of the Main Controller PCB SRAM Board.
All data on the SRAM Board is initialized.
Use case When clearing the RAM data of the Main Controller PCB SRAM
Board
Adj/set/operate method 1) Select the item, and then press OK key.
The machine is automatically rebooted.
2) Turn OFF/ON the main power switch.
Caution • Inform the user that all images in Inbox will be deleted and get
approval for it.
• Since the file management information is initialized, images on the
5
HDD cannot be read.
• Before execution of this item, be sure to output the service mode
setting values by P-PRINT. After execution, enter necessary
setting values.
• The RAM data is cleared after the main power switch is turned
OFF/ON.
Related service mode COPIER> FUNCTION> MISC-P> P-PRINT
CARD Clear of card ID-related data
Lv.1 Details To clear the data related to the card ID (department).
Use case When clearing the data related to the card ID
Adj/set/operate method 1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The value is cleared after the main power switch is turned OFF/ON.
W-TN-CLR Clear of waste toner full alarm & error
Lv.1 Details To clear the Waste Toner Container full alarm/error.
Use case When replacing the Waste Toner Container
Related service mode COPIER> ADJUST> MISC> WT-FL-LM
5-296
COPIER> FUNCTION> CLEAR
CA-KEY Deletion of CA certificate and key pair
Lv.2 Details To simultaneously delete the CA certificate and key pair which are
additionally registered by the user.
Use case When a service person replaces/discards the device
Adj/set/operate method 1) Select the item, and then press OK key.
2) Check that OK is displayed.
3) Turn OFF/ON the main power switch.
Caution • Unless this item is executed at the time of replacement/discard of
the device, the CA certificate and key pair which are additionally
registered by the user remain in the HDD, which is a problem in
terms of security.
• Do not execute this item carelessly because the CA certificate
and key pair which are additionally registered are deleted when
it is executed. If they are deleted mistakenly, they need to be
again registered by the user. If no CA certificate and key pair are
additionally registered, the machine condition becomes the same
as the one at the time of factory shipment.
• When NG is displayed in 2), there is a possibility that deletion
was not executed. In this case, surely execute the deletion by
initializing the HDD, etc.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Supplement/memo • The CA certificate is used in the MEAP application with E-RDS
and SSL client connection, and the key pair is used in the SSL
function of IPP, RUI and MEAP.
• When the main power switch is turned OFF/ON, the CA certificate
and key pair which were registered at the time of factory shipment
are decompressed from the archive (/BOOTDEV/KCMNG), and
become available in the E-RDS/SSL function.
ERDS-DAT Initialization of E-RDS SRAM data
Lv.1 Details To initialize the SCM value of the Embedded-RDS stored in the
SRAM.
SCM values are ON/OFF of E-RDS, server's port number, server's
SOAP URL, and communication schedule with the server (how often
the data is acquired), etc.
The value set by COPIER> FUNCTION> INSTALL> E-RDS, RGW-
PORT, RGW-ADR, COM-LOG is cleared.
Use case When upgrading the Bootable in the E-RDS environment
Adj/set/operate method Select the item, and then press OK key.
Caution The method of using the SRAM in E-RDS differs depending on the
Bootable version. Therefore, unless the SRAM data is cleared at the
time of version upgrade, data inconsistency occurs.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Related service mode COPIER> FUNCTION> INSTALL> E-RDS, RGW-PORT, RGW-ADR,
COM-LOG