Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 741

SORTER> ADJUST
STP-F2 Front 1-staple position(half size): Bklt
Lv.1 Details To adjust the A3/B4/A4/B5/LDR/LTR/EXEC/8K/16K paper front
1-staple position on Finisher.
As the value is incremented by 1, the staple position moves by
0.1mm.
+: Toward front
-: Toward rear
Use case When the A3/B4/A4/B5/LDR/LTR/EXEC/8K/16K paper front staple
position is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
STP-R1 Rear 1-staple position (R size): Bklt
Lv.1 Details To adjust the A4R/LGL/LTRR paper rear 1-staple position on
Finisher.
As the value is incremented by 1, the staple position moves by
0.1mm.
+: Toward front
-: Toward rear
Use case When the A4R/LGL/LTRR paper rear staple position is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
STP-R2 Rear 1-staple position (half size): Bklt
Lv.1 Details To adjust the A3/B4/A4/B5/LDR/LTR/EXEC/8K/16K paper rear
1-staple position on Finisher.
As the value is incremented by 1, the staple position moves by
0.1mm.
+: Toward front
-: Toward rear
Use case When the A3/B4/A4/B5/LDR/LTR/EXEC/8K/16K paper rear staple
position is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
SORTER> ADJUST
STP-2P Adj front/rear 2-staple position: Bklt
Lv.1 Details To adjust the front/rear 2-staple position on Finisher.
As the value is incremented by 1, the staple position moves by
0.1mm.
+: Toward front
-: Toward rear
Use case When the front/rear 2-staple position is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
BFF-SFT Paper displace amount on buffer: Bklt
Lv.1 Details To adjust the paper displacement amount on Finisher Buffer
Assembly.
As the value is incremented by 1, the paper position moves by 0.1mm.
+:
-:
Use case When the paper displacement occurs on the 1st to 3rd sheets of the
2nd sets (B5/A4/LTR) and later
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
PNCH-X Punch hole position in feed way: Bklt
Lv.1 Details To adjust the punch hole position on Finisher in feed direction.
As the value is incremented by 1, the punch hole moves by 0.1mm.
+: Toward delivery direction
-: Toward inlet direction
Use case When the punch hole is displaced in feed direction
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit 0.1 mm
Appropriate target value 0
TRM-RG1 Skew adj (small size): Bklt
Lv.1 Details To adjust the skew of A4 size or smaller paper stack on Finisher
Trimmer.
As the value is incremented by 1, the paper stack stop position
moves by 0.1mm.
+: Toward delivery direction
-: Toward inlet direction
Use case When the skew occurs on A4 or smaller paper stack
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
5
5-513