Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 288

■ ANALOG
COPIER> DISPLAY> ANALOG
TEMP Display of outside temperature
Lv.1 Details To display the temperature outside the machine.
This is measured by the Environment Sensor that measures the
outside air.
Use case When checking the temperature outside the machine
Display/adj/set range 0 to 60
Unit Deg C
Appropriate target value 20 to 27
Related service mode COPIER> DISPLAY> ANALOG> HUM, ABS-HUM, PDK-TEMP,
MDK-TEMP
HUM Display of outside humidity
Lv.1 Details To display the humidity outside the machine.
This is measured by the Environment Sensor that measures the
outside air.
Use case When checking the humidity outside the machine
Display/adj/set range 0 to 100
Unit %
Appropriate target value 30 to 70
Related service mode COPIER> DISPLAY> ANALOG> TEMP, ABS-HUM, PDK-HUM,
MDK-HUM
ABS-HUM Display of outside moisture amount
Lv.1 Details To display the absolute moisture amount outside the machine.
This is measured by the Environment Sensor that measures the
outside air.
Use case When checking the moisture amount outside the machine
5
Display/adj/set range 0 to 100
Unit g (g/m3)
Appropriate target value 0 to 22
Related service mode COPIER> DISPLAY> ANALOG> TEMP, HUM
DR-TEMP [Not Used]
FIX-UC Dis of Fixing Belt center temperature
Lv.1 Details To display the center temperature of the Fixing Belt detected by the
Fixing Main Thermistor.
Use case When checking the temperature at the center of Fixing Belt
Display/adj/set range 0 to 999
Unit Deg C
FIX-UE Dis of Fixing Belt rear edge temperature
Lv.1 Details To display the rear edge temperature of the Fixing Belt detected by
the Fixing Sub Thermistor 1.
Use case When checking the edge temperature of the Fixing Belt
Display/adj/set range 0 to 999
Unit Deg C
5-60
COPIER> DISPLAY> ANALOG
FIX-LC Dis of Pressure Belt center temperature
Lv.1 Details To display the center temperature of the Pressure Belt detected by
the Pressure Main Thermistor.
Use case When checking the temperature at the center of the Pressure Belt
Unit Deg C
Appropriate target value At standby: 90 to 140
At print: 70 to 150 (differs depending on modes)
FIX-LE Dis of Pressure Belt rear edge temp
Lv.1 Details To display the rear edge temperature of the Pressure Belt detected
by the Pressure Sub Thermistor 1.
Use case When checking the edge temperature of the Pressure Belt
Unit Deg C
Appropriate target value At standby: 70 to 190
At print: 70 to 190 (differs depending on modes)
FIX-LE2 Dis of Pressure Belt front edge temp
Lv.1 Details To display the front edge temperature of the Pressure Belt detected
by the Pressure Sub Thermistor 2.
Use case When checking the edge temperature of the Pressure Belt
Display/adj/set range 0 to 999
Unit Deg C
Appropriate target value At standby: 70 to 190
At print: 70 to 190 (differs depending on modes)
FIX-UE2 Dis of Fixing Belt front edge temp
Lv.1 Details To display the front edge temperature of the Fixing Belt detected by
the Fixing Sub Thermistor 2.
Use case When checking the edge temperature of the Fixing Belt
Display/adj/set range 0 to 999
Unit Deg C
DR-TEMPL [Not Used]
DEVHUM1 Dis of Y/M color Dev Ass'y humidity
Lv.2 Details To display the humidity of the Y and M Developing Assembly
detected by the Developing Assembly Inner Temperature Detection
PCB (Y/M).
Use case When a failure occurs on the developing contrast
Display/adj/set range 0 to 100
Unit %
Appropriate target value 5 to 80
Related service mode COPIER> DISPLAY> ANALOG> DEVHUM2, DEVTEMP1,
DEVTEMP2