Mitsubishi MELSEC-Q Series User Manual page 602

18
TROUBLESHOOTING
Table18.8 Common error codes returned by bus interface functions and MELSEC data link functions (Continued)
Return value
(HEX)
The Motion SFC program No. to start is outside the range 0 to 255
19458
(the error code returned by the Motion CPU).
(0x4C02)
Refer to the manual of used Motion CPU.
Axis No. set by SVST instruction is injustice. (the error code
19460
returned by the Motion CPU)
(0x4C04)
Refer to the manual of used Motion CPU.
Axis No. set by CHGA instruction is injustice. (the error code
19461
returned by the Motion CPU)
(0x4C05)
Refer to the manual of used Motion CPU.
Axis No. set by CHGV instruction is injustice. (the error code
19462
returned by the Motion CPU)
(0x4C06)
Refer to the manual of used Motion CPU.
Axis No. set by CHGT instruction is injustice. (the error code
19463
returned by the Motion CPU)
(0x4C07)
Refer to the manual of used Motion CPU.
There are 32 or more instruction requests to the Motion CPU from
the programmable controller CPU / C Controller module in sum
19464
table simultaneously, and the Motion CPU cannot process them.
(0x4C08)
(the error code returned by the Motion CPU)
Refer to the manual of used Motion CPU.
CPU No. of the instruction cause is injustice. (the error code
19465
returned by the Motion CPU)
(0x4C09)
Refer to the manual of used Motion CPU.
19584 H/W error of the target CPU (the error code returned by the
(0x4C80) Motion CPU)
19585 H/W error of the target CPU (the error code returned by the
(0x4C81) Motion CPU)
19587 H/W error of the target CPU (the error code returned by the
(0x4C83) Motion CPU)
19588 H/W error of the target CPU (the error code returned by the
(0x4C84) Motion CPU)
Q Corresponding MELSECNET/H Network System
Reference Manual (PLC to PLC network)
-475(0xFE25)
For QnA/Q4AR MELSECNET/10 Network System
to
Reference Manual
-3839(0xF101)
Type MELSECNET/10 Network system (PLC to PLC
network) Reference Manual
Destination station number specification error
-2174
The destination station number for the processing request is
(0xF782)
specifying the own station.
CC-Link System Master/Local Module User's Manual
-16386(0xBFFE)
Control & Communication Link System Master/Local
to
Module type AJ61QBT11/A1SJ61QBT11 User's Manual
-20222(0xB102)
Control & Communication Link System Master/Local
Module Type AJ61BT11/A1SJ61BT11 User's Manual
Destination station number specification error
-18558
The destination station number for the processing request is
(0xB782)
specifying the own station.
18
- 42 18.4 Error Code and Error Message Lists
18.4.1 Actions by error codes generated at function execution
Error description Corrective action
Check the user program on C Controller module.
Check the user program on C Controller module.
Check the user program on C Controller module.
Check the user program on C Controller module.
Check the user program on C Controller module.
Check the user program on C Controller module.
Check the user program on C Controller module.
Check the operation state of the target CPU.
Deal according to the manual of the target CPU.
Check the operation state of the target CPU.
Deal according to the manual of the target CPU.
Check the operation state of the target CPU.
Deal according to the manual of the target CPU.
Check the operation state of the target CPU.
Deal according to the manual of the target CPU.
Same as in the left
Check the specified station number.
Check if the station number 255(0xFF) is specified
to the own station.
Same as in the left
Check the specified station number.
(To next page)