Panasonic AFPX-C30R User Manual page 515

Num
Name
-ber
Basic function instruction
F137 Auxiliary
timer (16-bit)
Special instructions
F138 Hours, min-
P138 utes and sec-
onds to
seconds data
F139 Seconds to
P139 hours,
minutes and
seconds data
F140 Carry flag
P140 (R9009) set
F141 Carry flag
P141 (R9009) reset
F142 Watching
P142 dog timer
update
F143 Partial I/O
P143 update
F144 Serial data
communica-
tion control
F145 Data send
P145
F146 Data receive
P146
F145 Data send
P145
F146 Data receive
P146
F145 Data send
P145
F146 Data receive
P146
F145 Data send
P145
F146 Data receive
P146
F147 Printout
F148 Self-
P148 diagnostic
error set
F149 Message
P149 display
: Available, : Not available,
*1) The instruction is available for FP0 T32 (V2.3 or later) and FP-e.
*2) This instruction is available for FP0 V1.20 or later and FP-e.
*3) This instruction is available for FP-X V1.20 or later and FPΣ 32k type.
*4) This instruction is available for FP-X V2.50 or later and FPΣ V3.20 or later.
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Boo- Ope-
lean
rand
S, D Turns on the specified output and
STMR
R900D after 0.01 s × set value.
S, D Converts the hour, minute and second
HMSS
data of (S+1, S) to s econds d ata, and
PHMSS
the converted data is stored in (D+1, D).
S, D Converts the seconds data of (S+1, S)
SHMS
to hour, minute and second data,
PSHMS
and the converted data is stored in
(D+1, D).
- Turns on the carry flag (R9009).
STC
PSTC
- Turns off the carry flag (R9009).
CLC
PCLC
S The time (allowable scan time for the
WDT
system) of watching dog timer is
PWDT
changed to "S" × 0.1 (ms) for that scan.
D1, D2 Updates the I/O from the number
IORF
specified by "D1" to the number
PIORF
specified by "D2".
S, n The COM port received flag (R9038) is
TRNS
set to off to enable reception.
Beginning at "S", "n" bytes of the data
registers are sent from the COM port.
S1, S 2, Sends the data to another station in the
SEND
D, N network (MEWNET). (via link unit)
PSEND
S1, S 2, Receives the d ata to an other station
RECV
N, D in the network (MEWNET). (via link unit)
PRECV
S1, S 2, Sends the data to the slave station as
SEND
D, N the MOD bus master. (via COM port)
S1, S 2, Receives the data from the slave station
RECV
N, D as the MOD bus master. (via COM port)
S1, S 2, Sends the data to the slave station of
SEND
D, N the MOD bus master, type II.
S1, S 2, Receives the data from the slave station
RECV
N, D of the MOD bus master, type II.
S1, S 2, Sends the data to the slave station as
SEND
D, N the MEWTOCOL master. (via COM
port)
S1, S 2, Receives the data from the slave station
RECV
N, D as the MEWTOCOL master. (via COM
port)
S, D Converts the ASCII code data in the
PR
area starting with "S" for printing, and
outputs it to the word external output
relay WY specified by "D".
n Stores the self-diagnostic error number
ERR
(n: k 100 "n" in (DT9000), turns R9000 on, and
PERR
to K299) turns on the ERROR LED.
S Displays the character constant of "S" in
MSG
the connected programming tool.
PMSG
: Not available partially
Description
5
5
*1
5
*1
1
1
3
5
5
*2
9
9
9
*3
9
*3
9
*4 *4
9
*4 *4
9
*3 *3
9
*3 *3
5
3
13