Xerox DocuColor 1632 Service Manual page 780

Chain-Link Name
715-083 Pshad (4)
715-084 Pshad (5)
715-085 Pshad (6)
715-113 A6/Postcard Detection
715-114 A4S/8.5in Detection 1
715-115 A4S/8.5in Detection 2
715-116 Original detection table for special
paper
715-128 DADF FS Offset (side 2)
715-138 Document Size Detection
715-139 B5/8x10" Detection
715-140 8K Detection
715-141 8.5x13"/8.5x14" Detection
715-142 NutAngleF
715-143 NutAngleR
715-200 External Area of FS Sampling
715-204 Maximum Sampling Value of Back-
ground color
715-205 Initial Background color Value
715-208 Line to Fix Variation
715-212 Background Color Suppression mode
for BW
715-213 Background Color Suppression mode
for Color
715-214 Undercolor Data for BW
715-215 Undercolor Data for Color
715-218 Gamma Data for BW
715-219 Gamma Data for Color
715-220 Color Balance Default = Y/Low density 4
715-221 Color Balance Default = Y/Medium
density
715-222 Color Balance Default = Y/High density 4
715-223 Color Balance Default = M/Low density 4
715-224 Color Balance Default = M/Medium
density
715-225 Color Balance Default = M/High den-
sity
715-226 Color Balance Default = C/Low density 4
715-227 Color Balance Default = C/Medium
density
715-228 Color Balance Default = C/High density 4
General Procedures and Information
Table 3 Chain 715
Default Range Description
65 0~127 Red W-Ref Correction Coefficient P Paper Adjustment at factory.
72 0~127 Green W-Ref Correction Coefficient P Paper Adjustment at factory.
69 0~127 Blue W-Ref Correction Coefficient P Paper Adjustment at factory.
0 0~1 0 = A6 Document, 1 = Postcard Document (XC 0 = Postcard, 1 = A6)
0 0~1 0 = A4 Fixed (Other than XC), Letter Fixed (XC), 1 = Can be changed by Area Switching 2
3 0~6 0 = 210mm(A4S)~6 = 216mm(8.5")
0 0~2 0 = Do not use special table 1 = A Series (A4L when APS is Off, and A3S when APS is On) 2 = Inch Series
(Letter LEF when APS is Off, and 11x17" when APS is On)
71 01~50 Fast Scan Offset value (Dot) on IPS at DADF DUP Side 2. VLSS=PROMVLSS+PRadjF - 50 +DADF Offset Side
2 Adjustment at factory.
0 0~1 0 = Detection by 4 Registers, 1 = Detection by 3 Registers (Contamination Countermeasure)
0 0~1 B5/8x10" Switching (Default 0 = B5 Detection, 1 = 8x10" Detection)
0 0~1 8K detection specification (Default 0 = Do not detect, 1 = Detect)
0 0~1 8.5x13"/8.5x14" Detection Switching Specification in AP/XE markets.
990 0~1980 Front NUT Revolution Angle (990~1980 = Right revolution angle, 0~990 = Left revolution angle)
990 0~1980 Rear NUT Revolution Angle (990~1980 = Right revolution angle, 0~990 = Left revolution angle)
255 0~511 Speed Priority AE/Fast Scan direction undetected area
90 0~255 Speed Priority AE/Sampling Upper Limit/BMAX
0 0~255 Speed Priority AE/Background level initial value/INIT
48 0~255 Speed Priority AE/Slow Scan variation fixed position/NCON
2 0~2 Speed Priority AE/Suppression Mode Setup in B/W 0 = Register, 1 = Fixed, 2 = Vary
0 0~2 Speed Priority AE/Suppression Mode Setup in Color 0 = Register, 1 = Fixed, 2 = Vary
0 0~255 Speed Priority AE/Fixed background color data in B/W Register Mode
0 0~255 Speed Priority AE/Fixed background color data in Color Register Mode
1 0~2 AE GAMMA Data in B/W mode 0 = GMD=2, 1 = GMD=3, 2 = GMD=5
1 0~2 AE GAMMA Data in Color mode 0 = GMD=2, 1 = GMD=3, 2 = GMD=5
0~8 Default Color Balance Adjustment Level Y Color Low density
4 0~8 Default Color Balance Adjustment Level Y Color Medium density
0~8 Default Color Balance Adjustment Level Y Color High density
0~8 Default Color Balance Adjustment Level M Color Low density
4 0~8 Default Color Balance Adjustment Level M Color Medium density
4 0~8 Default Color Balance Adjustment Level M Color High density
0~8 Default Color Balance Adjustment Level C Color Low density
4 0~8 Default Color Balance Adjustment Level C Color Medium density
0~8 Default Color Balance Adjustment Level C Color High density
6/02
6-16
Prelaunch Training/Review
DC1632/2240