Xerox DocuColor 1632 Service Manual page 835

Table 1 Input Component Control Codes
Code Name
001-306 INTLK_3
004-100 Belt Home Sensor
004-101 Drum Motor YMC Fail Detec-
tion
004-102 Drum Motor K Fail Detection PR (Drum) Motor K Failure ON: High
004-200 FAN_LOCK_FAIL
005-102 Document Sensor
005-110 Regi Sensor (DADF)
005-115 Exit Sensor
005-119 Dup Sensor
005-150 #1 Size Sensor
005-151 #2 Size Sensor
005-201 Exchange from IISS
005-300 Platen I/L Switch
005-301 Top Cover I/L Switch
006-160 Polygon Motor Ready Signal Regular rotation of Polygon Motor ON: Low
006-201 Sheet Abort
006-212 IIT Regi Sensor
006-240 ADF Exist
006-251 APS Sensor1
006-253 APS Sensor3
006-272 PM-0
006-281 IPS Fan Fail
006-300 Platen I/L Switch
006-301 Angle Sensor
007-100 #1Tray Size SW1
007-101 #1Tray Size SW2
007-102 #1Tray Size SW3
007-103 #1Tray Size SW4
007-104 #2Tray Size SW1
007-105 #2Tray Size SW2
007-106 #2Tray Size SW3
007-107 #2Tray Size SW4
007-108 #3Tray Size SW1
007-109 #3Tray Size SW2
Prelaunch Training/Review
DC1632/2240
Description
High when Open is detected. ON: High
[Operation Description]: IBT is not at Home Posi-
tion. Open circuit. It is necessary to operate IBT
5V ON. ON: High
PR (Drum) Motor YMC Failure ON: High
Fan rotation is stopped ON: FAIL
No paper detected by Document Sensor ON:
High
Paper detected by Regi Sensor ON: Low
Paper detected by Exit Sensor ON: Low
Paper detected by Dup Sensor ON: Low
No paper detected by #1 Size Sensor ON: High
No paper detected by #2 Size Sensor ON: High
Document Exchange InstructiON. ON from IISS
ON: Low
Platen Cover Open ON: High
Top Cover Inter Lock Open ON: High
Document Regist ON: Low
Deactuation of Regi Sensor ON: Low
DADF is not installed ON: High
Document is detected ON: APS SNR1: Low, APS
ON: High
Document is detected ON: APS SNR3: Low, APS
ON: High
Flash Memory writing is not in progress ON:
Inside PWBA
High when FAN failure is detected. ON: High
Low when Platen closed. ON: Low
Low when Platen closed. ON: Low
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
Table 1 Input Component Control Codes
Code Name
007-110 #3Tray Size SW3
007-111 #3Tray Size SW4
007-112 #4Tray Size SW1
007-113 #4Tray Size SW2
007-114 #4Tray Size SW3
007-115 #4Tray Size SW4
007-116 #1Level Sensor
007-117 #2Level Sensor
007-118 #3Level Sensor
007-119 #4Level Sensor
007-120 #1Nopaper Sensor
007-121 #2Nopaper Sensor
007-122 #3Nopaper Sensor
007-123 #4Nopaper Sensor
007-125 SMH No paper Sensor
007-128 Face Up Tray Detect
008-100 #1Feed Out Sensor
008-102 #3Feed Out Sensor
008-103 #4Feed Out Sensor
008-104 Regi Sensor
008-105 Dup Wait Sensor
008-106 T/A Sensor
008-107 TTM Path Sensor1
008-108 TTM Path Sensor2
008-109 OHP Sensor#L
008-110 OHP Sensor#R
008-300 DUP Open Switch
009-101 Toner_Y New
009-102 Toner_M New
009-103 Toner_C New
009-104 Toner_K New
009-150 TNR FULL SNR
009-151 #Y_CRU detect
009-152 #M_CRU detect
6/02
6-71
Description
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
ON: AN value
Lift Up ON: High
Lift Up ON: High
Lift Up ON: High
Lift Up ON: High
No paper ON: High
No paper ON: High
No paper ON: High
No paper ON: High
No paper ON: High
Low when Tray is installed ON: Low
Paper detected ON: High
Paper detected ON: High
Paper detected ON: High
No paperON: Low
Paper detected ON: High
Paper detected ON: High
Paper detected
Paper detected
ON: Low
ON: Low
ON: High
CRU Connection of color is open (The CRU in
use is present, or it is not present) ON: Low=new,
High=old
CRU Connection of color is open (The CRU in
use is present, or it is not present) ON: Low=new,
High=old
CRU Connection of color is open (The CRU in
use is present, or it is not present) ON: Low=new,
High=old
CRU Connection of color is open (The CRU in
use is present, or it is not present) ON: Low=new,
High=old
ON: High
CRU is installed
CRU is installed
General Procedures and Information
dC330