Xerox DocuColor 1632 Service Manual page 839

Table 2 Output Component Control Codes
Code Name Description
009-026 #Y_BCR DC High voltage output value of BCR DC_Y.
ON: PWM
009-027 #M_BCR DC High voltage output value of BCR DC_M.
ON: PWM
009-028 #C_BCR DC High voltage output value of BCR DC_C.
ON: PWM
009-029 #K_BCR DC High voltage output value of BCR DC_K.
ON: PWM
009-030 #Y_BCR AC High voltage output value of BCR AC_Y.
ON: PWM
009-031 #M_BCR AC High voltage output value of BCR AC_M
009-032 #C_BCR AC High voltage output value of BCR AC_C
009-033 #K_BCR AC High voltage output value of BCR AC_K
009-034 [PSW Display] AGT AGITATOR MOT ON
MOT
009-035 CRUM PWR Power ON of CRUM-YMCK
009-038 BCR ACDC K CHG [Operation Description]: DEVE_AC_K
changes at connector terminals trailing.
009-039 BCRAC Clock Frequency signal common to BCR AC All
Colors.
009-040 ROS Shutter Close ROS Shutter: Rotates in Close direction
(Brush: Contact direction).
009-041 ROS Shutter Open ROS Shutter: Rotates in Open direction
(Brush: Retract direction). ON: HHH
009-042 #K_Erase Lamp K ERASE LAMP lit.
104mm/s
009-043 #K_Erase Lamp Not in use
52mm/s
009-044 #K_Erase Lamp Not in use
194mm/s
009-045 #YMC_Erase Lamp YMC ERASE LAMP lit.
104mm/s
009-046 #YMC_Erase Lamp Not in use
52mm/s
009-051 2nd BTR Contact Driving of BTR2RETMOT. Turns OFF
800ms after the Retract SNR detected the
Contact Position (High).
009-052 2nd BTR Retract Turns OFF 60ms after the Retract SNR
detected the Retract Position (Low).
009-053 De Tack Saw HV Turn on DTS HV.
009-054 1st BTR Contact Turns OFF 100ms after the Retract SNR
detected the Contact Position (High).
009-055 1st BTR Retract Turns OFF 100ms after the Retract SNR
detected the Retract Position (Low).
Prelaunch Training/Review
DC1632/2240
Conflicts Code Name
9-30 009-076 Specular reflection
LED
9-31
009-077 Diffusion reflection
LED
9-32
009-078 ADC Sensor Shut-
ter Open
9-33
009-079 ADC Sensor Shut-
ter Close
9-26
009-080 ATC Sensor 5V ON 5V Power supply to ATC SNR.
9-27 010-001 OCT Motor (CW)
9-28
010-002 OCT Motor (CCW) Turns ON reverse and turns OFF automati-
9-29
012-001 Main Drive Motor
On/Off
012-010 Rear Tamper Motor
Low Front On/Off
012-011 Rear Tamper Motor
Middle Front On/Off
9-41
012-012 Rear Tamper Motor
9-40
High Front On/Off
9-43, 9-44
012-013 Rear Tamper Motor
Low Rear On/Off
9-42, 9-44
012-014 Rear Tamper Motor
9-42, 9-43
Middle Rear On/Off
9-46
012-015 Rear Tamper Motor
High Rear On/Off
9-45
012-020 Staple Motor Close
- On/Off
012-021 Stapler Motor
Reverse
-
012-030 Eject Motor FOR-
WARD On/Off
-
- 012-031 Eject Motor
Reverse On/Off
-
6/02
6-75
Table 2 Output Component Control Codes
Description
When the Specular Reflection LED of ADC
SNR turns ON and YMC density is
detected.
When the Diffusion Reflection LED of ADC
SNR turns ON and K density is detected.
Turns OFF automatically after 100msec.
Turns OFF automatically after 100msec.
Turns ON forward and turns OFF automati-
cally at 150msec.
cally at 150msec.
[Operation Description]:
Turns OFF automatically after 100pulses.
Turns OFF automatically after 100pulses.
Turns OFF automatically after 100pulses.
Turns OFF automatically after 100pulses.
Turns OFF automatically after 100pulses.
Turns OFF automatically after 100pulses.
Stops at Home Position.
Turns OFF automatically after 110msec.
Turns OFF automatically after 2000pulses.
Turns OFF automatically after 2000pulses.
General Procedures and Information
Conflicts
-
-
9-79
9-78
-
010-002
010-001
12-71
12-11, 12-12,
12-13, 12-14,
12-15
12-10, 12-12,
12-13, 12-14,
12-15
12-10, 12-11,
12-13, 12-14,
12-15
12-10, 12-11,
12-12, 12-14,
12-15
12-10, 12-11,
12-12, 12-13,
12-15
12-10, 12-11,
12-12, 12-13,
12-14
12-21
12-20
12-31, 12-32,
12-33, 12-34,
12-41
12-30, 12-32,
12-33, 12-34,
12-4
dC330