Default Values For Interfaces - SICK GM32 Ex Operating Instructions Manual

Table 5: Connection data for intrinsically safe connections
Termi‐ Inlet sizes
nal
1 Inlet, temperature sensor
PT100, 3-wire circuit RMA42
2
3
4 Analog input, pressure sen‐
sor 4-20 mA RMA42
5
6 Digital input, pressure switch
1 KCD2-SR-Ex
7
8 Digital input, pressure switch
2 KCD2-SR-Ex
9
1) Max. inner capacity
2) Max. inner inductivity
2) Max. outer capacity
3) Max. outer inductivity
5) L/R ratio (inductivity/resistance)
6.3.1.2

Default values for interfaces

8015558/1O6S/V1-9/2024-08 | SICK
Subject to change without notice
Gas Uo Io
group
IIC ≤ 27.3 V ≤ 22.1
mA
IIB
IIB
IIC ≤ 27.3 V ≤ 96.5
mA
IIB
IIA
IIC 10.5V 17.1m
A
IIB
IIA
IIC 10.5V 17.1m
A
IIB
IIA
State State State State
Analog
Analog Digital Digital
Input
Output
Output Input
0...20mA
0...20mA
Signal
Relais
Sense
Load
500
100
1 2
1 2
1 2 1
2
3 4
3 4
Shield
Shield
DO2 DI1 DI2
DO1
AO1 AO2
AI1 AI2
DO3 DO4 DI3 DI4
- -
- -
11 21 11
21 11 21 11 21
12 22 12 22 12 22 12 22
13
23 23 13 23 13 23
13
14 24 14 24 14 24 14 24
Figure 15: Example: I/O module pin assignment
Analog input Pin assignment
AI 1 11, 12
AI 2 21, 23
AI 3 11, 12
NOTE
The analog input assignment shown in the Table is the default setting. The assignment
of the inputs can be freely configured with SOPAS. For more information, see the SOPAS
Operating Instructions.
ELECTRICAL INSTALLATION
Po Ui Ci Li
1) 2)
151 N/S 8 nF 75 μH
mW
659 N/S 8 nF 75 μH
mW
45m 12 V 0 0
W
45m 12 V 0 0
W
Function
Temperature (internally wired)
Pressure (internally wired)
Humidity
O P E R A T I N G I N S T R U C T I O N S | GM32 Ex
Co Lo μH/
2) 3)
Ω
≤ 85 nF ≤ 500 μH N/S
≤ 360 nF ≤ 2 mH N/S
≤ 530 nF ≤ 5 mH N/S
≤ 88 nF ≤ 4 mH N/S
≤ 683 nF ≤ 17 mH N/S
≤ 2 280 nF ≤ 34 mH N/S
2.41 µF ≤ 121.5 mH 801
≤ 16.8 µF ≤ 486.3 mH 1628
≤ 75 µF ≤ 972.7 mH 1628
≤ 2.41 µF ≤ 121.5 mH 801
≤ 16.8 µF ≤ 486.3 mH 1628
≤ 75 µF ≤ 972.7 mH 1628
6
2)
35