Philips IntelliVue X2 Instructions For Use Manual page 86

5 Patient Alarms and INOPs
INOP Message, Indication
SPIRO NO BREATH
SPIRO GAS COMPENS?
SPIRO PATIENT CAT.
Δ
SpO CHK SOURCES
2
Numeric is replaced by -?-
Δ
SpO CHK UNITS
2
Numeric is replaced by -?-
<SpO label> DEACTIVATED
2
INOP tone
<SpO label> EQUIP MALF
2
Numeric is replaced by -?-
INOP tone.
<SpO label> ERRATIC
2
Numeric is replaced by -?-
INOP tone.
<SpO label> EXTD. UPDATE
2
Label is displayed with a -?-
(questionable numeric)
<SpO label> INTERFERNCE
2
Numeric is replaced by -?-
INOP tone.
<SpO label> LOW PERF
2
Label is displayed with a -?-
(questionable numeric)
<SpO label> NOISY SIGN.
2
Numeric is replaced by -?-
INOP tone.
<SpO label> NON-PULSAT.
2
Numeric is replaced by -?-
INOP tone.
<SpO label> NO SENSOR
2
Numeric is replaced by -?-
INOP tone.
<SpO LABEL> POOR SIGNAL
2
Label is displayed with a -?-
(questionable numeric)
78
Source What to do
Spirometry No breath was detected for more than 25 seconds. Breath
derived numerics are not available.
Spirometry Gas compensation is set to "gas analyzer" but not all gases
necessary for compensation are measured by a gas monitor.
Some of the fall-back values provided by the user are used.
Measurement accuracy might be reduced.
Spirometry Mismatch of patient size configured in the host monitor and
sensor type plugged into the module. Check the instructions
on selecting the correct sensor in the Spirometry chapter.
SpO Not all measurements or values required to perform the
2
Difference calculation are available. Check measurement sources.
SpO The monitor has detected a conflict in the units used for this
2
Difference calculation. Check the unit settings.
SpO The SpO measurement label in the measurement device has
2 2
been deactivated by deactivating the label in the Measurement
Selection window. The measurement automatically disappears
from the display. To switch the measurement on again,
reactivate the measurement label in the Measurement Selection
window.
SpO The MMS or module is faulty. Unplug and replug the MMS or
2
module. If the INOP persists, contact your service personnel.
SpO Check the sensor placement. Try another adapter cable and
2
sensor. If the INOP persists, contact your service personnel.
SpO The update period of displayed values is extended due to an
2
NBP measurement on the same limb or an excessively noisy
signal.
SpO There is too much interference, caused by a high level of
2
ambient light and/or electrical interference. Cover the sensor to
minimize ambient light. If the INOP persists, make sure that
the sensor cable is not damaged or positioned too close to
power cables.
SpO Accuracy may be compromised due to very low perfusion.
2
Stimulate circulation at sensor site. If INOP persists, change
the measurement site.
SpO Excessive patient movement or electrical interference is causing
2
irregular pulse patterns. Try to reduce patient movement or to
relieve the cable strain on the sensor.
SpO Check the perfusion at measurement site. If necessary,
2
stimulate circulation or change measurement site. If the INOP
is due to NBP measurement on the same limb, wait until the
NBP measurement is finished.
SpO Make sure the SpO
2
try another adapter cable and sensor. If you silence this INOP,
the measurement will be switched off.
SpO The signal condition of the SpO
2
measurement accuracy may be compromised.
Technical Alarm Messages (INOPs)
sensor is connected. If the INOP persists,
2
measurement is poor and
2