Technical Data Confocaldt Ifd2411 - MICRO-EPSILON confocalDT IFD2410 Series Operating Instructions Manual

Functional Principle, Technical Data
2.5

Technical Data confocalDT IFD2411

Model
Measuring range
Start of measuring
range
Resolution
Measuring rate
4
Linearity
Multi-layer measurement
Light source
No. of characteristic curves
5
Permissible ambient light
Light spot diameter
6
Measuring angle
Numerical aperture (NA)
7
Minimum thickness
Target material
Synchronization
Supply voltage
Power consumption
Signal input
Digital interface
Analog output
Digital output
Connection
Mounting
Temperature range
Shock (DIN-EN60068-2-27)
Vibration (DIN EN 60068-2-6)
Protection class
(DIN-EN60529)
Material
Weight
No. of measurement channels
Control and display elements
FSO = Full Scale Output
1) Start of measuring range measured starting at sensor axis
2) Averaged over 512 values, at 1 kHz, in mid of measuring range on test glass
3) RMS noise in relation to mid of measuring range (1 kHz)
4) All data based on constant ambient temperature (25 ± 1°C) with measurement on plane-parallel test glass; data may deviate with
other targets
5) Light type: Incandescent lamp
6) Maximum sensor measuring angle up to which a usable signal on a reflective surface can be obtained at mid of measuring range,
in which the accuracy decreases towards the limit values
7) Pane of glass with refractive index n = 1.5 in mid of measuring range
8) No loss of intensity and linearity thanks to two synchronous measuring channels
confocalDT IFD2410/2411/2415
IFD2411-1
Distance 1.0 mm
approx. 15 mm
2 < 12 nm
Static
3
< 50 nm
dynamic
Distance < ±0.5 µm
Thickness < ±1.0 µm
12 µm
±25°
0.45
0.05 mm
Current: 4 ... 20 mA; current: 0 ... 5V & 0 ... 10 V (16 bit D/A converter)
Optical
Electrical
RJ45 connector for Ethernet (out) / EtherCAT (in/out) (max. cable length 100 m)
Storage
Operation
Sensor
Controller
Sensor Approx. 100 g
Controller
8
Multifunction key: Interface selection, two adjustable functions as well as reset to factory set-
IFD2411-2 IFD2411/90-2
2.0 mm
14 mm
9.6 mm
< 40 nm < 40 nm
< 125 nm < 125 nm
Continuously adjustable from 100 Hz to 8 kHz
< ±1.0 µm < ±1.0 µm
< ±2.0 µm < ±2.0 µm
Internal white LED
Saves up to 10 characteristic curves of different sensors,
selection via table in the menu
30,000 lx
10 µm
±12°
0.25
0.1 mm
Reflective, diffuse as well as transparent surfaces (e.g. glass)
24 VDC ±10 %
<max. 7 W (24 V)
Sync-In / trig-In; 1 x encoder (A+, A-, B+, B-, Index)
EtherCAT / RS422 / (Ethernet for configuration)
Plug-in optical fiber via E2000 connector, length 2 m ... 50 m,
min. bending radius 30 mm
3-pin supply terminal block;
5-pin I/O terminal block (max. cable length 30 m);
17-pin M12 connector for RS422, analog and encoder;
free-standing, DIN rail mounting
-20 ... +70 °C
Sensor: +5 ... +70 °C | Controller: +5 ... +50 °C
15 g/6 ms on XYZ axis, 1000 shocks each
2 g/20 ... 500 Hz on XYZ axis, 10 cycles each
Aluminum
Approx. 20 g Approx. 30 g
Approx. 335 g
ting after 10 s; 4x color LED for Intensity, Range, RUN and ERR
IFD2411-3
2.0 mm 3.0 mm
1
25 mm
< 40 nm
< 125 nm
< ±1.5 µm
< ±3.0 µm
1 layer
10 µm 18 µm
±12° ±19°
0.25 0.35
0.1 mm 0.15 mm
yes
Sync-out
IP64
IP40
Approx. 100 g
1
IFD2411-6
6.0 mm
35 mm
< 80 nm
< 250 nm
< ±3.0 µm
< ±6.0 µm
24 µm
±10°
0.18
0.3 mm
Approx. 100 g
Page 14