Lcd Indication - Fuji Electric FSJ Instruction Manual

LCD indication

Description
● Flow velocity display
Selectable flow velocity unit: m/s (if meters selected at SYSTEM UNIT) (See section 4.7.1.)
<Note> The decimal point position is fixed.(3 decimal points)
● Instantaneous volume flow rate display
Selectable instantaneous volume flow rate display: actual scale display, % display
<Note> The display unit is the unit selected at VOLUME FLOW RATE UNIT. (See Section 4.7.2)
● Instantaneous mass flow rate display
Selectable instantaneous mass flow rate display: actual scale display, % display
<Note> The display unit is the unit selected at MASS FLOW RATE UNIT. (See Section 4.7.4)
● Volume flow rate total display
Selectable total display: volume flow rate total actual scale (forward/reverse), flow rate total pulse count (forward/reverse)
<Note> The display unit is the unit selected at FLOW RATE TOTAL UNIT. (See Section 4.7.3)
Mass total display
Selectable total display: mass flow rate total actual scale (forward/reverse), mass total pulse count (forward/reverse)
<Note> The display unit is the unit selected at MASS TOTAL UNIT. (See Section 4.7.5)
● Pressure display
Pressure gauge pressure display read from analog input AI: actual scale display
<Note> The display unit is the unit selected at PRESSURE UNIT. (See Section 4.7.6)
● Temperature display
Thermometer temperature display read from analog input AI: actual scale display
<Note> The display unit is the unit selected at TEMPERATURE UNIT. (See section 4.7.7.)
The decimal point position is fixed.(°C: 1 decimal point, K: 2 decimal points)
● Pt temperature display
Resistance temperature detector temperature input temperature display: actual scale display
<Note> The display unit is the unit selected at TEMPERATURE UNIT. (See section 4.7.7.)
The decimal point position is fixed.(°C: 1 decimal point, K, °F: 2 decimal points)
● SNR display
S/N ratio display: dB
<Note> The decimal point position is fixed. (2 decimal points)
● AGC display
Wave receipt strength display: %
<Note> The decimal point position is fixed. (2 decimal points)
● Display setting method
Select DISPLAY setting mode "1st ROW" (1-row display) or "2nd ROW" (2-row display), and then select the display content.
For actual keying, refer to the typical operation indicated below. Set the protection to OFF beforehand. (See Section 4.4.1.)
Operation Set the 1st ROW of the LCD display to the VOLUME FLOW % display.
(example)
Key operation
Press the
▼
Press the
ENT
▼
Press the
▼
Press the
ENT
▼
Press the
ENT
▼
Press the
▼
Press the
ENT
▼ display "1:DECIMAL POINT".
Press the
▼
Press the
ENT
▼
▼
――― "VOLUME FLOW(%)" has been registered. ―――
Press the
ESC
enter the measurement mode.
Description
key twice to display "OUTPUT SETUP".
key once to display "ZERO ADJUSTMENT".
ENT
key for 3 times to display "DISPLAY".
key once to blink the cursor.
ENT
key again to select "1ST. LOW".
ENT
key twice to display "VOLUME FLOW(%)".
key once, and select and fix "VOLUME FLOW(%)" to
ENT
key once to shift the decimal point position to next place.
key once to register.
ENT
key for 3 times and then press the
ESC
key for 3 times to
－55－
Display
OUTPUT SETUP
ZERO ADJUSTMENT
DISPLAY
DISPLAY
1ST.ROW
1ST. LOW
VELOCITY
1ST. LOW
VOLUME FLOW(%)
1:DECIMAL POINT
 . 
1:DECIMAL POINT
 . 
1:DECIMAL POINT
 COMPLETE 
↓
1:DECIMAL POINT
 . 
0.00 %
0.000 m3
CLEAR