Fuji Electric FSJ Instruction Manual page 134

Setting unit
32 RATE LIMIT
33 RATE LIMIT TIMER
34 TOTAL MODE
35 VolumeTOTAL RATE *Note1
36 V:TOTAL PRESET
37 MASS TOTAL RATE *Note1
38 M:TOTAL PRESET
39 PULSE WIDTH *Note1
40 BURNOUT (TOTAL)
41 BURNOUT TIMER
42 DO1 OUTPUT TYPE
43 DO1 OUTPUT OPERATION
44 DO2 OUTPUT TYPE
45 DO2 OUTPUT OPERATION
46 AI RANGE KIND
47 AI BASE SCALE
48 AI FULL SCALE
49 COMMUNICATION BAUD RATE
50 COMMUNICATION PARITY
51 COMMUNICATION STOP BIT
52 COMMUNICATION
NO.
53 LIGHTS-OUT TIME
Note 1) When selecting "total pulse" for DO1 and DO2, specify the pulse width and total rate so that both of condition 1 and
condition 2 indicated below are satisfied.
Initial value
40.000 m 3 /h
1 0 sec
STOP
0 m 3
0 m
3
0 m
3
0 kg
50.0 msec
Hold
10 sec
Not used
Active ON
Not used
Active ON
NOT USED
0
0
38400 bps
Odd
1 bit
STATION 1
0
Setting value
[4.UNIT]
[sec]
START, STOP, TOTAL RESET
[5.UNIT]
[5.UNIT]
[7.UNIT]
[7.UNIT]
5.0 msec, 10.0 msec, 50.0 msec, 100.0 msec,
200.0 msec, 500.0 msec, 1000.0 msec
Not used, Hold
[sec]
 +Vol.TOTAL PULSE
 -Vol.TOTAL PULSE
 +MassTOTAL PULSE
 -MassTOTAL PULSE
 FULL SCALE 2
 ALARM [ALL, HARDWARE FAULT, PROCESS
ERROR]
 Vol.FLOW SWITCH
 Vol.FLOW SW HIGH [
 Vol.FLOW SW LOW [
 MassFLOW SWITCH
 MassFLOW SW HIGH [
 MassFLOW SW LOW [
 Vol.TOTAL SWITCH [
 MassTOTAL SWITCH [
 AO RANGE OVER
 PULSE RANGE OVER
 -: FLOW DIRECTION
 INPUT ALARM
 MAINTENANCE
Active ON, Active OFF
 +Vol.TOTAL PULSE
 -Vol.TOTAL PULSE
 +MassTOTAL PULSE
 -MassTOTAL PULSE
 FULL SCALE 2
 ALARM [ALL, HARDWARE FAULT, PROCESS
ERROR]
 Vol.FLOW SWITCH
 Vol.FLOW SW HIGH [
 Vol.FLOW SW LOW [
 MassFLOW SWITCH
 MassFLOW SW HIGH [
 MassFLOW SW LOW [
 Vol.TOTAL SWITCH [
 MassTOTAL SWITCH [
 AO RANGE OVER
 PULSE RANGE OVER
 -: FLOW DIRECTION
 INPUT ALARM
 MAINTENANCE
Active ON, Active OFF
NOT USED, PRESSURE, TEMPERATURE
[8. or 9.UNIT]
[8. or 9.UNIT]
9600 bps, 19200 bps, 38400 bps
None, Odd, Even
1 bit, 2 bits
[min]
－125－
Setting range
* Note1
[4.UNIT]]
[4.UNIT]]
[6.UNIT]]
[6.UNIT]]
[5.UNIT]]
[7.UNIT]]
* Note1
[4.UNIT]]
[4.UNIT]]
[6.UNIT]]
[6.UNIT]]
[5.UNIT]]
[7.UNIT]]