nord NORDAC FLEX SK 200E Series User Manual page 70

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
Pos : 165.1 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_00_Tabell enkopf_[SK 1xx E, SK 2xx E, SK 5xxP] @ 7\m od_1435561812889_14638.docx @ 228819 @ @ 1
Meaning, Functions
Terminal
No. Designation
Pos : 165.2 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_01_D OUT [SK 1x 0E, SK 2xx E] @ 7\m od_1435562956782_14638.doc x @ 229139 @ @ 1
Digital outputs
1 DOUT1
3 DOUT2
Pos : 165.3 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_01_D OUT _Ergänz ung [SK 2xx E] @ 7\mod_1435562960093_14638.docx @ 229171 @ @ 1
Note:
Size 4: Max. load 50 mA
SK 2x5E: Voltage level depending on input voltage level (18 – 30 V DC)
Pos : 165.4 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_02_AIN [SK 1x 0E, SK 2x 0E] @ 7\mod_1435563256730_14638.docx @ 229267 @ @ 1
Analog inputs
11 10V REF
14 AIN1+
16 AIN2+
40 GND
Pos : 165.5 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_02_AIN _Ergänz ung [SK 2x 0E] @ 7\mod_1435563260457_14638.docx @ 229299 @ @ 1
CAUTION: SK 200E and SK 210E: Use terminal 12 instead of terminal 40 (AGND/0 V)
Pos : 165.6 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_03_D IN [SK 2xxE] @ 7\mod_1435562625904_14638.docx @ 229011 @ @ 1
Digital inputs
21 DIN1
22 DIN2
23 DIN3
24 DIN4
Pos : 165.7 /Anleitungen/El ektr onik /FU und Starter/2. M ontage und Installation/Elek trischer Ansc hl uss/SK 1x xE, SK 2xx E, SK 5xxP, SK xxxE-FD S/Steuerteil/Details Steuer anschl üss e (Sammlung)/Details Steuer anschl üss e_04_TF [SK 1x xE, SK 2xx E] @ 7\m od_1435563263847_14638.docx @ 229331 @ @ 1
PTC thermistor input
38 TF+
39 TF-
Pos : 165.8 /Allgem ein/Allgemei ngültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0.doc x @ 2265496 @ @ 1
70
Description/Technical data
Meaning
Signaling of operating status of the device
24 V DC
With inductive loads: Provide protection
using freewheeling diode!
Digital output 1
Digital output 2
Actuation of device by external controller, potentiometer or similar device
Resolution 12 bit
U= 0...10 V, R =30 kΩ
i
I= 0/4 ... 20 mA
Burden resistance (250 Ω) via DIP switch
AIN1/2
Maximum permissible voltage at analog
input: 30 V DC
+ 10 V reference voltage
Analog input 1
Analog input 2
Reference potential GND
Actuation of device using an external controller, switch, or similar device.
HTL encoder connection possible with DIN2 and DIN3.
as per EN 61131-2, type 1
Low: 0-5 V (~ 9.5 kΩ)
High: 15-30 V (~ 2.5 - 3.5 kΩ)
Scan time: 1 ms
Reaction time: 4 - 5 ms
Digital input 1
Digital input 2
Digital input 3
Digital input 4
Monitoring of motor temperature using PTC
Use a shielded cable if the device is
installed near the motor.
PTC thermistor input
PTC thermistor input
Parameter
No. Function of factory setting
Maximum load 20 mA
P434 [-01] Fault
P434 [-02] Fault
The analog signals are adjusted via P402 and P403.
+ 10 V reference voltage: 5 mA not short-circuit-proof
11
40
10 kΩ
14
- -
P400 [-01] Setpoint frequency
P400 [-02] No function
- -
Input capacitance
10 nF (DIN1, DIN 4)
1.2 nF (DIN 2, DIN 3)
Cut-off frequency (only DIN 2 and DIN 3)
Min.: 250 Hz, max.: 205 kHz
P420 [-01] ON right
P420 [-02] ON left
P420 [-03] Fixed frequency 1 ( P465[-01])
P420 [-04] Fixed frequency 2 ( P465[-02])
The input is always active. In order to make the device
operational, a temperature sensor must be connected or both
contacts must be jumpered.
- -
- -
BU 0200 en-US-4920