Table of Contents
Advertisement
Pos : 537 /Anleitungen/El ektr onik /FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Param eter P541 – Rel ais und digital e Ausg äng e s etz en [SK 2x xE, SK 2xx E-FDS] @ 2\m od_1346932170278_14638.docx @ 43268 @ @ 1
Set relays
P541
(set digital output)
0000 ... FFF (hex)
This function provides the opportunity to control the relay and the digital outputs independently of
the variable frequency drive status. To do this, the relevant output must be set to the function
{ 0000 }
"External control".
This function can either be used manually or in combination with a bus control.
Bit 0 = Digital output 1
Bit 1 = Bus/AS-i Out Bit 0
Bit 2 = Bus/AS-i Out Bit 1
Bit 3 = Bus/AS-i Out Bit 2
Bit 4 = Bus/AS-i Out Bit 3
Bit 5 = Bus/An/Dig Out Bit 4,
Changes which are made to the settings are not saved in the EEPROM. After "Power ON" of the
variable frequency drive, the parameter is therefore in the default setting.
Setting of the value via ...
BUS:
Simple Box:
Parameter Box:
Pos : 538 /Anleitungen/El ektr onik /FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P500- P599/Param eter P542 – Analogausgang s etz en [SK 1x 0E, SK 2x xE, SK 2xx E-FDS] @ 2\mod_1346932170902_14638.docx @ 43292 @ @ 1
P542
Set analog output
[-01]
(set analog output)
[-02]
[-01] = IOE-1, AOUT of the first I/O extension (SK xU4IOE)
0.0 ... 10.0 V
[-02] = IOE-2, AOUT of the second I/O extension (SK xU4IOE)
{ all 0.0 }
... only with
The analog output of the VFD can be set with this function, independently of the actual operating
SK CU4-IOE or
state. To do this, the relevant analog output must be set to the function "External control" (P418 =
SK TU4-IOE
7).
This function can either be used manually or in combination with a bus control. The value set here
will, once confirmed, be produced at the analog output.
Changes which are made to the settings are not saved in the EEPROM. After "Power ON" of the
variable frequency drive, the parameter is therefore in the default setting.
Pos : 539 /Allgem ein/Allgem eingültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0.doc x @ 2265496 @ @ 1
BU 0200 en-US-4920
"Bus/Analog/Digital Out Bit 4"
Bits 8-11
0000
Min. value
0
1111
Max. value
F
The corresponding hex value is written into the parameter, thereby setting the
relay and digital outputs.
The hexadecimal code is entered directly when the Simple Box is used.
Each individual output can be separately called up in plain text and activated.
Bit 6 = Bus/An/Dig Out Bit 5,
"Bus/Analog/Digital Out Bit 5"
Bit 7 = Bus digital output 7
Bit 8 = Bus digital output 8
Bit 9 = Bus statusword Bit10
Bit 10 = Bus statusword Bit13
Bit 11 = Digital output 2
Bits 7-4
Bits 3-0
0000
0000
0
0
1111
1111
F
F
5 Parameter
S
Binary
hex
Binary
hex
S
201
Advertisement
Table of Contents
