nord NORDAC FLEX SK 200E Series User Manual page 217

Pos : 623 /Anleitungen/El ektr onik /FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Param eter P744 – Aus baustufe [SK 1x 0E, SK 2xx E, SK 2xxE-FD S] @ 2\m od_1346932209541_14638.docx @ 43676 @ @ 1
Configuration level
P744
(configuration level)
0000 ... FFFF This parameter displays the devices integrated in the VFD. Display is in hexadecimal code
(hex)
(Simple Box, bus system).
The display is in plain text when the Parameter box is used.
High byte:
Pos : 624 /Anleitungen/El ektr onik /FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Param eter P744 – Aus baustufe_Teil 2/2 [SK 2xxE] @ 9\mod_1448455671379_14638.docx @ 266930 @ @ 1
00
hex
01
hex
02
hex
03
hex
Pos : 625 /Anleitungen/El ektr onik /FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Param eter P747 – Umrichters pannungsbereic h [SK 1x0E, SK 2xx E, SK 2x xE-FD S] @ 9\m od_1448457030116_14638.docx @ 266996 @ @ 1
P747 Inverter voltage range
(inverter voltage range)
0 ... 2 Indicates the line voltage range for which this device is specified.
0 = 100 – 120 V
Pos : 626 /Anleitungen/El ektr onik /FU und Starter/5. Par ameter/Par ameter auflistung (P000 ...)/P700- P799/Param eter P748 – Status CAN open [SK 1x0E, SK 2xxE, SK 2xx E-FDS] @ 2\mod_1346932210180_14638.doc x @ 43700 @ @ 1
Status CANopen
P748
(CANopen status
0000 ... FFFF Shows the status of the system bus.
(hex)
or
Bit 0:
0 ... 65535
(dec)
Bit 1:
Bit 2:
Bit 3:
Bit 4:
Bit 5:
Bit 6:
Bit 7:
Bit 8:
Bit 9:
Bit 10:
Pos : 627 /Allgem ein/Allgem eingültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0.doc x @ 2265496 @ @ 1
BU 0200 en-US-4920
No extension
Encoder
Posicon
---
1 = 200 – 240 V
(system bus statu))
24 V bus supply voltage
CANbus in "Bus Warning" status
CANbus in "Bus Off" status
System bus → Bus module online (field bus module, e.g.: SK xU4-PBR)
System bus → Additional module 1 online (I/O - module, e.g.: SK xU4-IOE)
System bus → Additional module 2 online (I/O - module, e.g.: SK xU4-IOE)
The protocol of the CAN module is
Vacant
"Bootup Message" sent
CANopen NMT State
CANopen NMT State
CANopen NMT State
Stopped
Pre-operational
Operational
Low byte:
00 Standard I/O
hex
01 STO
hex
02 AS-i
hex
03 STO and AS-i
hex
04 Standard I/O
hex
05 STO
hex
06 AS-i
hex
07 STO and AS-i
hex
0 = CAN/1 = CANopen
Bit 10 Bit 9
0 0
0 1
1 0
5 Parameter
(SK 205E)
(SK 215E)
(SK 225E)
(SK 235E)
(SK 200E)
(SK 210E)
(SK 220E)
(SK 230E)
2 = 380-480 V
217