nord NORDAC FLEX SK 200E Series User Manual page 230

NORDAC FLEX (SK 200E ... SK 235E) – Users Manual for Frequency Inverters
19.1 Star/delta incorrect
"Motor star/delta circuit
incorrect"
Pos : 681 /Allgem ein/Allgem eingültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0.doc x @ 2265496 @ @ 1
Pos : 682 /Anleitungen/El ektr onik /FU und Starter/6. M eldung en zum Betriebsz ustand/Störm eldung en (Auflistung)/F ehl er E020 / E021 [SK 135E ... SK 5xx E/P, SK xxx E-FDS] @ 2\mod_1347454288768_14638.doc x @ 46902 @ @ 1
E020 20.0 Reserved
E021
20.1 Watchdog
20.2 Stack overflow
20.3 Stack underflow
20.4 Undefined opcode
20.5 Protected Instruct.
"Protected Instruction"
20.6 Illegal word access
20.7 Illegal Inst. Access
"Illegal instruction access"
20.8 Prog. memory error
"Program memory error"
(EEPROM error)
20.9 Dual-ported RAM
21.0 NMI error
(Not used by hardware)
21.1 PLL error
21.2 ADU error "Overrun"
21.3 PMI error "Access Error"
21.4 User stack overflow
Pos : 683 /Anleitungen/El ektr onik /FU und Starter/6. M eldung en zum Betriebsz ustand/Störm eldung en (Auflistung)/F ehl er E022 "res erviert" - PLC [SK 180E ... SK 5xx E/SK 500P] @ 2\mod_1361527702934_14638.docx @ 59092 @ @ 1
E022 --- Reserved
Pos : 684 /Anleitungen/El ektr onik /FU und Starter/6. M eldung en zum Betriebsz ustand/Störm eldung en (Auflistung)/F ehl er E023 "res erviert" - PLC [SK 180E ... SK 5xx E/SK 500P] @ 2\mod_1361527808170_14638.docx @ 59117 @ @ 1
E023 --- Reserved
Pos : 685 /Anleitungen/El ektr onik /FU und Starter/6. M eldung en zum Betriebsz ustand/Störm eldung en (Auflistung)/F ehl er E024 "res erviert" - PLC [SK 180E ... SK 5xx E/ SK 500P] @ 6\m od_1423644411761_14638.docx @ 201829 @ @ 1
E024 --- Reserved
Pos : 686 /Allgem ein/Allgem eingültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0.doc x @ 2265496 @ @ 1
230
• Check motor connection
• Check preset motor data (P201 ... P209)
• PMSM – CFC Closed Loop Operation: Rotor position
of motor incorrect in relation to incremental encoder
Determine rotor position (initial enable after a "Power
On" only with motor stationary) (P330)
System error in program execution, triggered by EMC
interference.
• Observe wiring guidelines
• Use additional external mains filter
• VFD must be very well grounded
Error message for PLC  see supplementary manual
0550
Error message for PLC  see supplementary manual
0550
Error message for PLC  see supplementary manual
0550
BU
BU
BU
BU 0200 en-US-4920