Komatsu HB365LC-3 Operation & Maintenance Manual page 500

Headrest - Remove / Install................................ 3-165
High register range (treble) - Adjust....................3-240
High-pressure hoses and pipings - Handle...........2-47
Horizontal pin type tooth - Use..............................6-33
Horn - Check.......................................................3-161
Horn switch........................................................... 3-91
Hybrid caution lamp.............................................. 3-22
Hybrid system stop caution lamp.......................... 3-30
Hybrid temperature caution lamp..................3-22,3-42
Hydraulic breaker..................................................6-34
Hydraulic circuit - Bleed air............................. 4-3,4-42
Hydraulic circuit - Connect.................................... 6-14
Hydraulic circuit - Release internal pressure........ 4-76
Hydraulic circuit - Switch.......................................6-15
Hydraulic circuit for machine ready for installation of
attachment - Change-over / Connect.............6-13
Hydraulic oil filter element - Replace.................... 4-64
Hydraulic oil temperature caution lamp.................3-21
Hydraulic oil temperature gauge........................... 3-39
Hydraulic system - Warm-up operation...............3-184
Hydraulic system caution lamp............................. 3-24
Hydraulic tank - Change oil...................................4-86
Hydraulic tank - Check oil level / Add oil.............3-152
Hydraulic tank additional breather element - Replace.
.......................................................................4-70
Hydraulic tank strainer - Clean..............................4-73
If any problem is found..........................................2-20
If machine monitor shows warning display......... 3-275
Indicator - Check electrolyte level......................... 4-49
Initial 250 hours maintenance (only 1st maintenance
of new machine)............................................ 4-16
Inside operator's compartment............................. 2-20
Inspecting machine............................................... 2-19
Introduction............................................................. 1-8
Investigate and confirm jobsite conditions............ 2-27
Jumper cable - Connect......................................3-268
Jumper cable - Disconnect................................. 3-269
KCCV filter element - Replace.............................. 4-77
KDPF - Clean........................................................4-85
KDPF - Handle.................................................... 3-118
KDPF soot accumulation caution lamp................. 3-25
KDPF system caution lamp...................................3-24
Keep machine clean............................................. 2-19
Keep work place clean and tidy............................ 2-41
Komatsu Closed Crankcase Ventilation (KCCV) 3-128
Komatsu genuine lubricants....................................4-2
Komatsu genuine replacement parts...................... 4-2
KOMTRAX.......................................................... 3-143
KomVision.............................................................6-39
8-4
I
J
K
Lamp switch.......................................................... 3-91
Language - Set..................................................... 3-83
Left front mirror - Adjust...................................... 3-166
Left front mirror (A) - Adjust to the regular position......
.....................................................................3-166
Lift capacity chart - 1-piece boom........................... 5-3
Lifting of personnel prohibited...............................2-23
Lifting operation by using bucket with hook.......... 2-40
Loading and unloading with trailer...................... 3-243
Loading work.......................................................3-210
Location of EU regulations, engine serial No. plate.....
....................................................................... 1-11
Location of product identification number (PIN)/
machine serial No. plate.................................1-11
Location of safety labels......................................... 2-5
Lock.................................................................... 3-216
Lock inspection cover............................................. 4-3
Lock lever..............................................................3-99
Lock lever automatic lock cancel switch............... 3-93
Lock lever pilot lamp............................................. 3-36
Lock pin.................................................................6-10
Long-life tooth - Use..............................................6-33
Long-term storage.................................................6-24
Low fuel consumption by hybrid system................. 1-9
Low register range (bass) - Adjust...................... 3-240
Lower wiper switch................................................3-96
Lubrication chart..................................................... 7-5
Machine - Change direction during straight travel........
.....................................................................3-196
Machine - Check walk-around............................ 3-145
Machine - Escape from mud............................... 3-208
Machine - Lift...................................................... 3-255
Machine - Load................................................... 3-244
Machine - Lubricate.............................................. 4-51
Machine - Operation after warm-up operation.... 3-189
Machine - Park....................................................3-214
Machine - Raise using block ................................ 4-41
Machine - Raise using slope.................................4-40
Machine - Running-in the new machine..............3-181
Machine - Secure................................................3-246
Machine - Secure with tie down point................. 3-247
Machine - Secure without tie down point............ 3-247
Machine - Set at angle.......................................... 4-40
Machine - Start (Travel forward and reverse) / Stop....
.....................................................................3-192
Machine - Start after long-term storage.............. 3-260
Machine - Steer........................................ 3-195,3-197
Machine - Steer (Change the direction).............. 3-195
Machine - Stop....................................................3-194
Machine - Travel forward.................................... 3-193
Machine - Travel reverse.................................... 3-194
Machine - Unload................................................3-253
Machine equipment name.......................................3-2
INDEX
L
M