AUMA ACE C 01.2 Profinet Series Manual page 49

Actuator controls
AC 01.2/ACExC 01.2 Profinet
ID Type Parameters
PRM 3693 enum Priority REMOTE
PRM 3694 enum Fieldbus auto enable
Table 51: Customer settings > I/O interface
ID Type Parameters
Data length = 4 bytes
PRM 519 enum Self-retaining Remote
PRM 533 enum Self-retaining Remote
II
Table 52: Customer settings > Positioner
ID Type Parameters
Data length = 30 bytes
PRM 84 enum Adaptive behaviour
PRM 87 U16 Outer dead band
PRM 86 U16 Dead time
PRM 2012 U16 Dead band OPEN
PRM 213 U16 Dead band CLOSE
PRM 2916 U16 Posit. hyst. OPEN
PRM 2917 U16 Posit. hyst. CLOSE
PRM 5316 U16 Dead band min. (ad.2)
PRM 5317 U16 Dead band max. (ad.2)
PRM 215 I32 Tolerance CLOSE
PRM 214 I32 Tolerance OPEN
PRM 4167 enum Limit setting range
Access Default Setting value
R/W 0 0: Selector switch Local
1: Sel. sw. Local + Off
R/W 1 0: Off
1: On
Ac- Default Setting value
cess
R/W 3 0: Off (push-to-run op.)
1: OPEN
2: CLOSE
3: OPEN and CLOSE
4: OPEN & CL w/o STOP
R/W 0 0: Off (push-to-run op.)
1: OPEN
2: CLOSE
3: OPEN and CLOSE
4: OPEN & CL w/o STOP
Ac- Default Setting value
cess
R/W 0 0: Off
1: Adaptive I
R/W 10 Min = 1 [0.1 %]
Max = 100 [0.1 %]
R/W 5 Min = 2 [0.1 s]
Max = 600 [0.1 s]
R/W 5 Min = 0 [0.1 %]
Max = 100 [0.1 %]
R/W 5 Min = 0 [0.1 %]
Max = 100 [0.1 %]
R/W 5 Min = 0 [0.1 %]
Max = 50 [0.1 %]
R/W 5 Min = 0 [0.1 %]
Max = 50 [0.1 %]
R/W 2 Min = 2 [0.1 %]
Max = 50 [0.1 %]
R/W 25 Min = 2 [0.1 %]
Max = 50 [0.1 %]
R/W 0 Min = 0 [0.1 %]
Max = 50 [0.1 %]
R/W 1000 Min = 950 [0.1 %]
Max = 1000 [0.1 %]
R/W 0 0: Function not active
1: Function active
Appendix
Explanation
Preserving the operation mode
REMOTE in selector switch po-
sition LOCAL or OFF depending
on the enable signal
Automatic generation of enable
signal for priority REMOTE
function in case loss of fieldbus
communication
Explanation
Setting the operation behaviour
(push-to-run operation or self-
retaining) for binary operation
commands (OPEN, STOP,
CLOSE) from remote.
Setting the self-retaining Re-
mote II mode
Explanation
Setting the adaptive behaviour
of the positioner
Setting the outer dead band (ir-
relevant for adaptive behaviour)
Setting the dead time
Setting dead band OPEN (irrel-
evant for adaptive behaviour)
Setting dead band CLOSE (irrel-
evant for adaptive behaviour)
Hysteresis in direction OPEN
(for adaptive positioner only)
Hysteresis in direction CLOSE
(for adaptive positioner only)
Minimum dead band Xt (adapt-
ive positioner 2)
Maximum dead band Xt (adapt-
ive positioner 2)
Tolerance for the function
"Closing fully" for end position
CLOSED
Tolerance for the function
"Opening fully" for end position
OPEN
Function Limit setting range
49