At^slck Facility Lock; At+Cpwd Define And Change Password - Multi-Tech MultiModem EDGE Reference Manual

5.5 AT^SLCK Facility Lock

AT^SLCK provides the "Facility lock" function as defined for the GSM 07.07 command
Description:
AT+CLCK. The command can be used to lock, unlock or interrogate a network or ME <facility>.
AT^SLCK is, in every respect, identical with AT+CLCK, except that the command syntax and
response prefix is "^SLCK" instead of "+CLCK". For further details please refer to AT+CLCK.
The command can be aborted when network facilities are being set or interrogated.
Test Command Syntax:
Response(s):
Write Command Syntax:
Response(s):
In the airplane mode the write command version for the network related <facility> (AO, OI, OX, AI, IR, AB, AG
Note:
and AC) is not supported. For remaining facilities the command is fully functional then.

5.6 AT+CPWD Define and Change Password

AT+CPWD allows to define a new password for a password protected <facility> lock function.
Description:
Each password is a string of digits, the length of which varies with the associated <facility>. The
test command returns a list of pairs which represent the available facilities and the maximum
length of the associated password. See AT commands AT+CLCK and AT^SLCK for more
information on the various lock features.
Specifically the command can be used to
•
change PIN1 or PIN2,
•
change the password supplied from your provider for the "call barring" supplementary service,
•
set individual phone security passwords,
• enter the unblocking key (Master Phone Code) to restore a disabled "PS" password.
To delete a password use the following syntax: at+cpwd=<facility>,<old password>
Test Command Syntax:
Response(s):
Write Command Syntax:
Response(s):
Parameter Descriptions:
<facility>
Phone security locks set by client or factory:
Primarily intended for the client to take safety precautions. Passwords "SC" (SIM PIN) and "P2" (SIM PIN2) are
usually predefined, but can be configured individually. The lock facility password "PS" may also be factory set.
"SC" SIM PIN. SIM requests password upon ME power-up and when this lock command is issued.
If incorrectly entered three times, the SIM PUK is required to perform authentication.
Input of the SIM PUK password is possible only with AT command AT+CPIN or ATD. For further
details please refer to Section 5.1.1, What to do if PIN or password authentication fails?.
<password length>: 4 to 8 digits.
"PS" Phone locked to SIM card. ME requests password when other than current SIM card is inserted.
"PS" lock is frequently referred to as "phone lock", or "device lock". Accordingly, the password
may be called "phone code" or "device code". The "PS" password is not associated with the PUK
of the SIM card. It must be defined before the first use of <facility> "PS" with AT+CLCK.
<password length>: 4 digits.
If incorrectly entered three times, the Master Phone Code is required to lift the lock. This
Unblocking procedure is performed with AT+CPWD using the following parameters:
<facility>="PS", <old password>=Master Phone Code (obtained from the module manufacturer)
and <new password>= the new phone code ("PS" password for lock facility), if desired.
Remember that a successful PIN authentication is a prerequisite for use of AT command
AT+CPWD. If Pin authentication has not been completed, input of the Master Phone code
password is possible only with AT command AT+CPIN or ATD. For further detail please refer to
Section 5.1.1, What to do if PIN or password authentication fails?
Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371G)
AT^SLCK=?
^SLCK:list of supported <facility>s,
AT^SLCK=<facility>, <mode>[, <password>][, <class>]
if <mode> is not equal 2 and command successful: OK
if <mode>=2 and command successful: ^SLCK: <status>, <class>
If error is related to ME functionality:
AT+CPWD=?
+CPWD : (list of supported (<facility>, <password length>)
OK
AT+CPWD=<facility>, <old password>[, <new password>]
New password has been registered for the facility lock function.
OK
If parameter <old password> was not correct: +CME ERROR 16 (+CME ERROR:
incorrect password)
If the password for the selected <facility> has been invalidated due to too many failed
attempts: +CME ERROR ...
If error is related to ME functionality: +CME ERROR
Chapter 5 – Security Commands
OK
[^SLCK: <status>, <class>]
[^SLCK: ...]
OK
+CME ERROR
73