Multi-Tech MultiModem EDGE Reference Manual page 48

"simstatus" SIM Status Indication
The SIM Status indicator allows the MC75 to output the status of the subscriber
identity module (SIM) via URC.
0
1
2
3
4
5.
"band" Currently selected frequency band or band combination.
1...14
"simlocal" Availability of the SIM card, physically connected
0
1
If RSA is active: The AT^SIND "simlocal" URC refers to the unused local SIM.
The status of the remote SIM card currently used for the RSA connection is controlled by
AT^SCKS.
If RSA is inactive: The AT^SIND "simlocal" URC refers to the currently used local SIM. In this
case the value is identical to the AT^SCKS value, except for AT^SCKS value 2.
<indValue>
Integer type value in the range stated above for the corresponding <indDescr>.
Notes specific to the EONS feature:
If the indicator is "eons", the <indValue> is a type associated to the operator name according to GSM 22.101.
This type depends on the source of the operator name.
Priority of types associated to the operator names is defined as follows (the type listed first has the highest
priority). If a type cannot be indicated the next one will be used.
0 Not registered.
1 EF-OPL and EF-PNN (alphanumeric format, can contain up to 24 characters.)
2 Operator Name String in long and short format according to Common PCN Handset Specification
(CPHS) (alphanumeric format, can contain up to 16 characters).
3 Name information received by the NITZ service long and short form (alphanumeric format, can contain
up to 16 characters). The short form will be displayed only if EF
4 Any operator name stored internal to the ME (alphanumeric format, can contain up to 16 characters).
5 Broadcast MCC-MNC (numeric format which consists of a 3-digit country code plus a 2- or 3-digit
network code).
The name information received by the NITZ service (type 3) will be saved in the non-volatile RAM. It replaces
the operator name of the registered PLMN (type 4) or its numeric form (type 5) stored in the ME. However,
when after restart the ME registers to another PLMN that is not equal to the saved NITZ name information, the
NITZ name information must be invalidated.
If the type is 2, 4 or 5, AT+COPS with the appropriate <mode> displays the same operator name.
<mode>
0 Indicator is deregistered; i.e., no such indicator event report (URC) will be issued. <mode>=0 is power-up
and factory default of indicators defined by AT^SIND only.
1 Indicator is registered.
•
Indicator event reports are controlled via AT+CMER.
• All indicators can be registered or deregistered via AT^SIND, but different default settings apply:
Power-up and factory default of the indicators supported by AT+CIND is <mode>=1, while, as stated
above, indicators defined by AT^SIND only are set to <mode>=0.
2 Query the registration status and the current value of a single indicator type.
Multi-Tech Systems, Inc. AT Commands for EDGE Modems (S000371G)
SIM card removed.
Note: Another way to verify the SIM card connection is the "^SCKS"
URC enabled with AT^SCKS. For use after restart, its presentation mode can be
stored to the user profile with AT&W.
SIM card inserted.
SIM PIN1 not required - SIM card unlocked. MC75 automatically registers to the
GSM network without requesting SIM PIN1.
SIM PIN1 required - SIM card locked. SIM PIN1 must be entered to enable MC75
to register to the GSM network.
Personalization info ready - CHV (Card Holder Verification) data has been
verified (if required).
SIM initialization completed - ME has finished reading SIM data.
Note: Another way to notify the user when SIM data are accessible is the "^SSIM
READY" URC enabled with AT^SSET. For use after restart, its presentation
mode can be stored to the user profile with AT&W.
Identical with <rbc> of AT^SCFG. The value indicates the band(s) currently
available for network selection, depending on the network configuration either a
single band or a dual band combination. The URC appears whenever the status
of the currently available band(s) changes, for example after using the AT^SCFG
command to change the "Radio/Band" parameters <rba> or <rbp>. Please see
AT^SCFG for further detail about the feature "Radio/Band" selection.
SIM removed.
SIM inserted.
Chapter 3 – Status Control Commands
from CPHS is available.
OPShort
48