Toshiba TEC B-SX4T Series Maintenance Manual page 6

5.5 PRINTER PARAMETER FINE ADJUSTMENT ----------------------------------------------------------5-41
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
5.5.7
5.6 TEST PRINT ------------------------------------------------------------------------------------------------------5-50
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
5.6.7
5.6.8
5.6.9
5.7 SENSOR ADJUSTMENT--------------------------------------------------------------------------------------5-59
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
5.8 RAM CLEAR ------------------------------------------------------------------------------------------------------5-63
5.8.1
5.8.2
5.8.3
5.8.4
5.9 IP ADDRESS SETTING ---------------------------------------------------------------------------------------5-67
5.10 BASIC SETTING-------------------------------------------------------------------------------------------------5-70
5.10.1 Basic Specification Selection Mode------------------------------------------------------------------- 5-70
5.10.2 Basic File Browser ---------------------------------------------------------------------------------------- 5-71
5.10.3 Basic Trace Selection Mode ---------------------------------------------------------------------------- 5-71
5.10.4 Basic Expansion Mode----------------------------------------------------------------------------------- 5-71
5.11 RFID Module Setting--------------------------------------------------------------------------------------------5-72
5.11.1 RFID Read Test-------------------------------------------------------------------------------------------- 5-73
5.11.2 RFID Carrier Sense Test (B-SX704-RFID-U2 only)----------------------------------------------- 5-75
5.11.3 RFID Module Type Selection --------------------------------------------------------------------------- 5-75
5.11.4 RFID Tag Type Selection-------------------------------------------------------------------------------- 5-76
5.11.5 RFID Module's Destination Code Setting (U2 Module Only) ----------------------------------- 5-79
5.11.6 RFID Error Tag Detection ------------------------------------------------------------------------------- 5-80
5.11.7 Maximum Number of RFID Issue Retries ----------------------------------------------------------- 5-84
5.11.8 Maximum Number of RFID Read Retries ----------------------------------------------------------- 5-85
5.11.9 RFID Read Retry Time-out------------------------------------------------------------------------------ 5-86
5.11.10 Maximum Number of RFID Write Retries------------------------------------------------------------ 5-87
5.11.11 RFID Write Retry Time-out------------------------------------------------------------------------------ 5-88
5.11.12 RFID Adjustment for Retry ------------------------------------------------------------------------------ 5-89
5.11.13 RFID Wireless Power Level Setting------------------------------------------------------------------- 5-90
5.11.14 RFID AGC Threshold and RFID Channel Setting ------------------------------------------------- 5-91
Mantenimiento Periféricos Informáticos C/Canteras,15 28860 Paracuellos de Jarama Madrid Tel: 91 748 16 04 www.mpi.com.es
Feed Length Fine Adjustment -------------------------------------------------------------------------- 5-42
Cut/Strip Position Fine Adjustment-------------------------------------------------------------------- 5-43
Back Feed Length Fine Adjustment------------------------------------------------------------------- 5-45
X Axis Fine Adjustment ---------------------------------------------------------------------------------- 5-46
Print Tone Fine Adjustment (Thermal Transfer/Thermal Direct Print) ------------------------ 5-47
Ribbon Motor Voltage Fine Adjustment (Feed/Take-up Motor) -------------------------------- 5-48
Threshold Manual Fine Adjustment (Black Mark/Feed Gap Sensor) ------------------------- 5-49
Specifying the Print Condition for the Test Print --------------------------------------------------- 5-52
Test Print Pattern Selection----------------------------------------------------------------------------- 5-55
Slant Line (1 dot) ------------------------------------------------------------------------------------------ 5-55
Slant Line (3 dots) ----------------------------------------------------------------------------------------- 5-56
Characters -------------------------------------------------------------------------------------------------- 5-56
Barcode ------------------------------------------------------------------------------------------------------ 5-57
Non-Printing ------------------------------------------------------------------------------------------------ 5-57
Factory Test ------------------------------------------------------------------------------------------------ 5-58
Auto Print ---------------------------------------------------------------------------------------------------- 5-58
Sensor Status Display------------------------------------------------------------------------------------ 5-60
Black Mark Sensor Adjustment ------------------------------------------------------------------------ 5-61
Feed Gap Sensor Adjustment-------------------------------------------------------------------------- 5-61
Black Mark Sensor and Feed Gap Sensor Adjustment (No Paper)--------------------------- 5-62
Ribbon End Sensor Adjustment ----------------------------------------------------------------------- 5-62
RAM Clear Menu Selection ----------------------------------------------------------------------------- 5-63
No RAM Clear ---------------------------------------------------------------------------------------------- 5-64
Maintenance Counter Clear----------------------------------------------------------------------------- 5-64
Printer Parameter Clear---------------------------------------------------------------------------------- 5-64
EO18-33012B
(Revision Date: Jan. 30, 2009)