Page 1 TEC Thermal Printer B-SX4T/SX5T SERIES Maintenance Manual Document No. EO18-33012B Original Jan., 2003 (Revised Feb., 2003 Jan., 2006) PRINTED IN JAPAN Mantenimiento Periféricos Informáticos C/Canteras,15 28860 Paracuellos de Jarama Madrid Tel: 91 748 16 04 www.mpi.com.es...
Page 2 WARNING! Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. NOTES: 1. Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation. 2.
Page 3: Table Of Contents
EO18-33012B (Revision Date: Feb. 15, 2007) TABLE OF CONTENTS Page UNPACKING-------------------------------------------------------------------------------------------------------- 1- 1 PROCEDURES ---------------------------------------------------------------------------------------------------1- 1 CHECKS ------------------------------------------------------------------------------------------------------------1- 3 PRINTER INSTALLATION-------------------------------------------------------------------------------------- 1- 3 NOTE FOR OPTIONAL EQUIPMENT INSTALLATION /MAJOR UNIT REPLACEMENT/MAINTENANCE---------------------------------------------------- 3- 1 OPENING/CLOSING THE TOP COVER-------------------------------------------------------------------3- 3 REMOVING THE SIDE PANEL (L) --------------------------------------------------------------------------3- 3 OPENING/CLOSING THE PRINTER BLOCK ------------------------------------------------------------3- 4 REMOVING THE OPERATION PANEL --------------------------------------------------------------------3- 5 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT ------------------------------------- 4- 1...
Page 4 EO18-33012B (Revision Date: Feb. 6, 2009) 4.14 STRIP MODULE (B-9904-H-QM-R) ------------------------------------------------------------------------4-90 4.14.1 Applicable Model ------------------------------------------------------------------------------------------ 4-90 4.14.2 Packing List ------------------------------------------------------------------------------------------------- 4-90 4.14.3 Installation Procedure ------------------------------------------------------------------------------------ 4-91 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R)------------------------------------------------------ 4-100 4.15.1 Applicable Model -----------------------------------------------------------------------------------------4-100 4.15.2 Packing List ------------------------------------------------------------------------------------------------4-100 4.15.3 Installation Procedure -----------------------------------------------------------------------------------4-101 4.16 PCMCIA INTERFACE BOARD (B-9700-PCM-QM-R) ----------------------------------------------- 4-106 4.16.1 Applicable Model -----------------------------------------------------------------------------------------4-106...
Page 5 EO18-33012B (Revision Date: May 22, 2009) 4.25 RFID MODULE (B-SX704-RFID-U2-CN-R) ------------------------------------------------------------ 4-209 4.25.1 Applicable Model -----------------------------------------------------------------------------------------4-210 4.25.2 Packing List ------------------------------------------------------------------------------------------------4-211 4.25.3 Installation Procedure -----------------------------------------------------------------------------------4-212 4.25.4 RFID Module Setting ------------------------------------------------------------------------------------4-230 4.25.5 AGC Threshold Setting ---------------------------------------------------------------------------------4-234 4.26 IDENTIFICATION OF THE RFID MODULE (B-SX704-RFID-U2-US/EU/AU/CN-R) ---------------4-237 SYSTEM MODE---------------------------------------------------------------------------------------------------- 5- 1 OPERATION PANEL --------------------------------------------------------------------------------------------5- 1 OVERVIEW --------------------------------------------------------------------------------------------------------5- 2...
Page 6 EO18-33012B (Revision Date: Jan. 30, 2009) PRINTER PARAMETER FINE ADJUSTMENT ----------------------------------------------------------5-41 5.5.1 Feed Length Fine Adjustment -------------------------------------------------------------------------- 5-42 5.5.2 Cut/Strip Position Fine Adjustment-------------------------------------------------------------------- 5-43 5.5.3 Back Feed Length Fine Adjustment------------------------------------------------------------------- 5-45 5.5.4 X Axis Fine Adjustment ---------------------------------------------------------------------------------- 5-46 5.5.5 Print Tone Fine Adjustment (Thermal Transfer/Thermal Direct Print) ------------------------ 5-47 5.5.6 Ribbon Motor Voltage Fine Adjustment (Feed/Take-up Motor) -------------------------------- 5-48 5.5.7...
Page 7 EO18-33012B (Revision Date: Jul. 24, 2009) 5.11.15 RFID Channel Setting ------------------------------------------------------------------------------------ 5-92 5.11.16 RFID Module Q Value Setting-------------------------------------------------------------------------- 5-92 5.11.17 AGC Theshold for Data Write Setting ---------------------------------------------------------------- 5-93 5.11.18 AGC Threshold Lower Limit for Retry Setting ------------------------------------------------------ 5-94 5.11.19 Hibiki Tag Multi Word Write ----------------------------------------------------------------------------- 5-95 5.12 Z-MODE------------------------------------------------------------------------------------------------------------5-96 5.12.1 Z-Mode Setting Selection-------------------------------------------------------------------------------- 5-97 5.13 DOWNLOAD MODE --------------------------------------------------------------------------------------------5-98...
Page 8 CD-ROM. The other specifications including the firmware are common. CAUTION! 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC. 2. The contents of this manual may be changed without notification.
Page 9: Unpacking
1. UNPACKING EO18-33012B 1.1 PROCEDURE 1. UNPACKING NOTE: The pictures provided in this manual are of the B-SX4T series with the serial number of 3T311410 or earlier. Please note that they are partly different from the B-SX4T series with the serial number of 3T311411 or later and B-SX5T series with the serial number of 3Wxxxxxx or later.
Page 10 1. UNPACKING EO18-33012B 1.1 PROCEDURE 5) Open the top cover and remove the five pieces of tape. And then, open the ribbon shaft holder plate to remove the ribbon shaft pad from the printer. Top Cover Tape Ribbon Shaft Pad Tape OPEN Tape...
Page 11: Checks
1. UNPACKING EO18-33012B 1.2 CHECKS 1.2 CHECKS 1) Check for damage or scratches on the printer. 2) Confirm that none of the accessories are missing. The parts below are provided as accessories. Warranty Registration (QQ model only) Power Cord Fan Filter QC Card (QQ model only) Ferrite Core (B-SX5T series only) CD-ROM...
Page 12: Note For Optional Equipment Installation /Major Unit Replacement/Maintenance
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33012B /MAINTENANCE 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT/MAINTENANCE 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION /MAJOR UNIT REPLACEMENT/MAINTENANCE WARNING! 1. Turn the power off and disconnect the power cord before replacing the main parts. Power Switch Power Cord 2.
Page 13 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33012B /MAINTENANCE 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT/MAINTENANCE 2. Do not remove the screws below. Doing so will require the printer block position adjustment with the jig. Printer Block Screw 3.
Page 14: Opening/Closing The Top Cover
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33012B /MAINTENANCE 3.1 OPENING/CLOSING THE TOP COVER 3.1 OPENING/CLOSING THE TOP COVER When opening the top cover, fully open the top cover to the open position. When closing, softly close it to the close position. Open Position Close Position 3.2 REMOVING THE SIDE PANEL (L)
Page 15: Opening/Closing The Printer Block
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33012B /MAINTENANCE 3.3 OPENING/CLOSING THE PRINTER BLOCK In case of RFID-ready printers, disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L). Fan Motor Harness CN19 Side Panel (L) Fan Motor...
Page 16: Removing The Operation Panel
3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33012B /MAINTENANCE 3.4 REMOVING THE OPERATION PANEL 3.4 REMOVING THE OPERATION PANEL 1) Open the top cover. (Refer to section 3.1.) 2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 3) Remove the SMW-4x8 screw that secures the operation panel ass’y.
Page 17 3. NOTE FOR OPTIONAL EQUIPMENT INSTALLATION/MAJOR UNIT REPLACEMENT EO18-33012B /MAINTENANCE 3.4 REMOVING THE OPERATION PANEL 6) Disconnect the operation panel harness from the operation panel ass’y. Operation Panel Ass’y Operation Panel Harness Hook Bottom Plate 7) Reassemble in the reverse order of removal. Lead the operation panel harness through the bush so that the side panel (L) does not catch it.
Page 18: Installation Procedure For Optional Equipment
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT WARNING! 1. Make sure to unplug the power cord before installing the optional equipment. 2. Be careful not to pinch your fingers or hands with the covers. CAUTION! When replacing parts or performing maintenance on the printer, be careful not to damage the print head with a hard object like a watch or a ring.
Page 19 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 1) Turn the power off and disconnect the power cord. 2) When the printer is used in the batch or strip mode: Remove the two black screws to detach the front plate. NOTE: Retain the two black screws and front plate.
Page 20 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 8) Remove the expansion I/O board from the printer temporarily using the following procedure: (1) Disconnect the expansion I/O cable from CN1 on the Expansion I/O board. (2) Remove the two B-3x6 screws to detach the expansion I/O board from the printer.
Page 21: Swing Cutter (B-4205-Qm)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.1 SWING CUTTER (B-4205-QM) 4.1 SWING CUTTER (B-4205-QM) WARNING! Be careful not to injure your fingers when installing the cutter unit. Cutter Blade This optional device is used for cut print, which cannot be used together with either B-8204-QM or B- 9904-H-QM.
Page 22 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.1 SWING CUTTER (B-4205-QM) 2) Open the top cover. (Refer to Section 3.1.) 3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 4) Open the print head block. (Refer to Section 3.3.) 5) Attach the cutter unit to the front of the printer with the cutter attachment screws and the FL-4x6 screw.
Page 23 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.1 SWING CUTTER (B-4205-QM) 9) Close the print head block and the ribbon shaft holder plate. NOTE: DO NOT excessively push down the print head block to close it. Doing so may cause a failure of the print head block or damage to the print head.
Page 24: Rotary Cutter (B-8204-Qm)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.2 ROTARY CUTTER (B-8204-QM) 4.2 ROTARY CUTTER (B-8204-QM) WARNING! Be careful not to injure your fingers when installing the cutter unit. Cutter Blade This optional device is used for cut print, which cannot be used together with either B-4205-QM or B- 9904-H-QM.
Page 25 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.2 ROTARY CUTTER (B-8204-QM) 2) Disassemble the frame into 3 parts. Rotary Cutter Guide Plate B SMW-4x8 SMW-3x6 Rotary Cutter PC Board Cover Rotary Cutter Guide Plate C (To be used later.) 3) Replace the Rotary Cutter Guide Plate B and the Rotary Cutter Guide Plate C with the Rotary Cutter Frame A and Rotary Cutter Frame B, respectively.
Page 26 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.2 ROTARY CUTTER (B-8204-QM) NOTE: When attaching the B-8204-QM cutter module, replace the original cutter paper guide C with the enclosed B-SX cutter paper guide C using the following procedure. CAUTION! Do not hold the cutter paper guides when attaching the Cutter Unit to the printer. Doing so may deform the cutter paper guides, causing a paper jam.
Page 27 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.2 ROTARY CUTTER (B-8204-QM) 1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 2) Open the top cover. (Refer to Section 3.1.) 3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 4) Fix the cutter drive unit to the printer with the three SM-4x8 screws.
Page 28 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.2 ROTARY CUTTER (B-8204-QM) 7) Insert the harness ass’y into the hole in the main frame. Fit the bush into the hole. Main Frame Hole Harness Ass’y 8) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively.
Page 29 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.2 ROTARY CUTTER (B-8204-QM) 11) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws. Cutter Unit SM-4 x 8 Screw SM-4 x 8 Screw Notch Notch...
Page 30: Strip Module (B-9904-H
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.3 STRIP MODULE (B-9904-H-QM) 4.3 STRIP MODULE (B-9904-H-QM) This optional device is used for strip print, which cannot be used together with either B-4205-QM or B- 8204-QM. When using a strip module together with an RFID module, be sure to install the RFID module prior to the strip module.
Page 31 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.3 STRIP MODULE (B-9904-H-QM) 1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 2) Open the top cover. (Refer to Section 3.1.) 3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 4) Remove the operation panel ass’y from the printer.
Page 32 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.3 STRIP MODULE (B-9904-H-QM) 8) Fit the bush to the longer harness of the rewind full sensor (Tr) and the rewinder harness in the orientation shown below. Rewinder Ass’y SM-4x8B Screw SM-4x8C Screw Notch Longer Harness of the Rewind Full Sensor (Tr)
Page 33 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.3 STRIP MODULE (B-9904-H-QM) 10) Connect the longer harness of the rewind full sensor (Tr) and the rewinder harness to CN4 and CN15 on the Main PC board, respectively. CN15 Main PC Board Longer Harness of the Rewind Full Sensor (Tr) Rewinder Harness...
Page 34 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.3 STRIP MODULE (B-9904-H-QM) 13) Secure the strip sensor (LED) and strip sensor (Tr) to the printer with the SM-4x8B screws. 14) Connect the shorter harness of the strip sensor (Tr) to the strip sensor harness (for LED). Strip Sensor SM-4x8B Screw (Tr)
Page 35 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.3 STRIP MODULE (B-9904-H-QM) 16) Fix the strip sensor harness with the three cable clamps and connect it to CN20 on the Main PC board. Main PC Board CN20 Cable Clamp Strip Sensor Harness 17) Reassemble the side panel (L) in the reverse order of removal.
Page 36: Ribbon Saving Module (B-9904-R/R2
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.4 RIBBON SAVING MODULE (B-9904-R/R2-QM) 4.4 RIBBON SAVING MODULE (B-9904-R/R2-QM) All the following parts are supplied with the kit. Make sure you have all items shown below. NOTE: The ribbon saving module is standard on the B-SX5T series. Solenoid (1 pc.) RSV PC Board (1 pc.) Solenoid Harness (1 pc.)
Page 37 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.4 RIBBON SAVING MODULE (B-9904-R/R2-QM) 4) Secure the RSV PC board to the printer with the locking supports. RSV PC Board Holes for securing the RSV PC Board Locking Support NOTE: Do not push the center of the RSV PC board when attaching it to the printer. Doing so may break the PC board.
Page 38 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.4 RIBBON SAVING MODULE (B-9904-R/R2-QM) 6) Attach the cable clamp to the frame of the printer. Fix the solenoid cable with this cable clamp. Cable Clamp Solenoid Cable Solenoid Solenoid Harness NOTE: Be careful not to snag the solenoid harness when running it. 7) Connect the solenoid harness to CN1 on the RSV PC board and CN11 on the Main PC board.
Page 39 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) This optional interface board is provided with the two slots, which allows for the use of the two TYPE II PC cards. However, it is not applied to TYPE III PC cards. CAUTION! 1.
Page 40: Pcmcia Interface Board (B-9700-Pcm
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) NOTE: In case of the B-SX5T or the B-SX4T that the optional Expansion I/O board (B-7704-IO-QM) has been installed in, remove the expansion I/O board from the printer temporarily using the following procedure.
Page 41 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 6) Secure the PCMCIA interface board to the PCB support plate with the SM-3x6 screw. Tighten the two M-3x5 screws that were loosened previously. (Refer to Caution) PCB Support Plate M-3x5 Screw SM-3x6 screw 7) Attach the blind plate A to the rear plate with the two SM-3x6 screws that were removed in step...
Page 42: Usb Interface Board (B-9700-Usb
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.6 USB INTERFACE BOARD (B-9700-USB-QM) 4.6 USB INTERFACE BOARD (B-9700-USB-QM) This optional interface board is provided with the interface port, which allows for the installation of USB devices. CAUTION! 1. Loosen the two M-3x5 screws of the USB interface board before installing it. Failure to do this may cause damage to the connector.
Page 43 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.6 USB INTERFACE BOARD (B-9700-USB-QM) 5) If the PCMCIA interface board is used together with the USB interface board, attach the PCB attachment plate to the plate to which the PCMCIA interface board is secured with the SM-3x6 screw.
Page 44 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.6 USB INTERFACE BOARD (B-9700-USB-QM) 7) Secure the USB interface board to the rear plate with the two SM-3x6 screws. When connecting to the PCMCIA Interface Board: When connecting to the Main PC Board: USB Interface Board USB Interface Board SM-3x6 Screw...
Page 45 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.6 USB INTERFACE BOARD (B-9700-USB-QM) 10) Attach the blind plate A to the rear plate. If the PCMCIA interface board has been installed, go to the next step. Blind Plate A Rear Plate SM-3x6 Screw NOTE: In case that the PCMCIA interface board has been installed, retain the blind plate A.
Page 46: Lan Interface Board (B-9700-Lan
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) This optional interface board enables the printer to be used in a LAN network. CAUTION! 1. Loosen the two M-3x5 screws of the LAN interface board before installing it. Failure to do this may cause damage to the connector.
Page 47 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 1) Loosen the two M-3x5 screws of the LAN interface board. (Refer to Caution above.) 2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 3) Remove the two SM-3x6 screws to remove the blind plate A from the back.
Page 48 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 5) Firmly connect CN50 on the LAN interface board directly to CN7 on the Main PC board or CN1 on the PCMCIA interface board. When connecting to the PCMCIA Interface Board When connecting to the Main PC Board CN50 CN50...
Page 49 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 7) Tighten the two M-3x5 screws on the LAN interface board that were loosened previously. (Refer to Caution.) 8) Secure the LAN interface board to the PCB support plate (when connecting to the Main PC board) or PCB attachment plate (when connecting to the PCMCIA interface board) with the SM-3x6 screw.
Page 50: Expansion I/O Interface Board (B-7704-Io
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) This optional interface board is provided with an expansion I/O interface. NOTE: The expansion I/O interface board is standard on the B-SX5T series. All the following parts are supplied with the kit.
Page 51 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 5) Connect the expansion I/O cable to CN3 on the Main PC board. Main PC Board Expansion I/O Cable 6) Secure the expansion I/O board to the rear plate with the two B-3x6 screws removed in Step 4. 7) Connect the expansion I/O cable to CN1 on the expansion I/O board.
Page 52: Ribbon Saving Module And Rotary Cutter (For B-Sx4T Series)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) When using the rotary cutter on the B-SX4T series, the ribbon saving module needs to be installed, also.
Page 53 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) WARNING! Be careful not to injure your fingers when installing the cutter unit. Cutter Blade When attaching the B-8204-QM cutter module, replace the original cutter paper guide C with the enclosed B-SX cutter paper guide C using the following procedure.
Page 54 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) (2) Secure the B-SX cutter paper guide C with the M-4x6 set screws while pushing it upward. M-4x6 B-SX Cutter Paper Guide C Installation Procedure 1) Remove the side panel (L) from the printer.
Page 55 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) 5) Insert folded tag paper (1.5-mm thick) between the print head and the platen, and then turn the head lever to Lock position. Insert the head up arm into the plunger of the solenoid. While holding down the head up arm slightly, lift the solenoid.
Page 56 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) 7) Connect the solenoid harness to CN1 on the RSV PC board and CN11 on the Main PC board. Pass the solenoid harness through the cut. 8) Connect the solenoid cable to CN2 on the RSV PC board.
Page 57 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) 12) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively. Harness Ass’y CN9 (2 pins) CN7 (9 pins) 13) Fit the bush to the harness ass’y in the orientation as shown below.
Page 58 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) 15) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC board, respectively. CN15 (9 pins) CN18 (2 pins) Main PC Board Harness Ass’y...
Page 59 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.9 RIBBON SAVING MODULE AND ROTARY CUTTER (For B-SX4T Series) 18) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws. Cutter Unit SM-4 x 8 Screw SM-4 x 8 Screw...
Page 60: Applicable Model
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) NOTES: 1. An RFID tag chip or the print head may be damaged when the print head passes over the chip. This can be prevented by using the ribbon saving module (standard feature for the B-SX5T and optional for the B-SX4T).
Page 61 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.10 RFID MODULE (B-9704-RFID-U1-US/EU) Parts Quantity Parts Quantity RFID Module Ribbon Guide 1 pc. 1 pc. 1 pc. 1 pc. Bush Cable Clamp 1 pc. 1 pc. 1 pc. 1 pc. Interface Cable SMW-3x6 Double Sems Screw 1 pc.
Page 62 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.10 RFID MODULE (B-9704-RFID-U1-US/EU) 4.10.3 Removing the Platen Frame Top and Attaching the Ribbon Guide NOTE: When installing an RFID module, be care of the following: 1. When an RFID module is used together with a cutter module or strip module, install the RFID module first.
Page 63 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.10 RFID MODULE (B-9704-RFID-U1-US/EU) 6) Remove the following three screws. SMW-3x6 Screw SMW-4x8 Screw 7) Remove the Platen Frame Top from the printer. Platen Frame Top 8) Remove the four screws from the side of the Print Head Block, slightly pull the Head Side Plate, and remove the two Ribbon Guide Shafts.
Page 64 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.10 RFID MODULE (B-9704-RFID-U1-US/EU) 9) Insert one of the Ribbon Guide Shafts removed in Step 12 into the Ribbon Guide. Rotate the Ribbon Guide Shaft so that its D-cut is in the same orientation with the Ribbon Guide’s D-cut. NOTE: Without doing this, the Ribbon Guide cannot be fit in the Print Head Block.
Page 65 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) 4.10.4 Attaching the Antenna The procedure for attaching the Antenna Frame and the Antenna Cover is provided below. Be careful the procedure is partly different between the US model and the EU model. US Model Raise the Print Head Block, and slide the Antenna Frame containing the Antenna into the printer as shown below.
Page 66 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) Push the Antenna Cover backward, and secure it with the two SMW-3x6 screws. Antenna Cover SMW-3x6 Screw EU Model Raise the Print Head Block, and slide the Antenna Frame into the printer as shown below. Let the protruding screw of the printer pass through the slit of the Antenna Frame.
Page 67 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) 3) Mount the Antenna Cover containing the Antenna on the inside of the Antenna Frame. Be sure to fit the locating pins of the Antenna Cover into the oval holes and the cuts in the Antenna Frame.
Page 68: Attaching The Rfid Module
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) 4.10.5 Attaching the RFID Module Attach the Cable Clamp to and fit the Bush into the positions shown in the picture below. Pass the Antenna Cable through the Bush, and fix the cable with the Cable Clamp Cable Cable Clamp...
Page 69 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) Connect CN1 on the RFID Module to CN14 on the Main PC Board with the Interface Cable. CN14 RFID Module Interface Cable Main PC Board 5) Connect the Antenna Cable to the RFID Module until it clicks.
Page 70 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) 6) Fit the tab of the RFID Module into the slot in the RFID Module Cover, and attach the RFID Module Cover to the RFID Module with the SMW-3x6 screw. Pass the Interface Cable and the Antenna Cable through the openings of the RFID Module Cover, respectively.
Page 71: Parameter Setting And Operation Check For The Rfid Module
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) 8) An FCC sticker is supplied with the B-9704-RFID-U1-US model, and a CE sticker is supplied with the B-9704-RFID-U1-EU/EU-R model, respectively. After installing the RFID module in the printer, please attach the sticker to the specified location on the printer.
Page 72: Rfid Module (B-9704-Rfid-H1-Qm/Qm
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Feb. 15, 2007) 4.10 RFID MODULE (B-9704-RFID-U1-US/EU/EU-R) Print the Maintenance Counter/Parameter Settings and the Self-Diagnostic Test result to confirm the RFID Module status. Example: Maintenance Counter/Parameter Settings Label Make sure that [U1] is selected and other parameters for the RFID Module are printed as follows.
Page 73: Applicable Model
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Jan. 19, 2007) 4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R) 4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R) NOTES: 1. An RFID tag chip or the print head may be damaged when the print head passes over the chip. This can be prevented by using the ribbon saving module (standard feature for the B-SX5T and optional for the B-SX4T).
Page 74 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM) Parts Quantity Parts Quantity Cable Clamp RFID Plate 1 pc. 1 pc. SMW-3x6 Double Sems Screw PT-3x6 P-TITE Screw 7 pcs. 1 pc. Interface Cable SMW-2x10 Double Sems Screw 1 pc.
Page 75 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM) Wiring Diagram RFID Module Interface Cable Pin No. Signal Color Brown Orange /RTS Black /CTS Black /DTR Black /DSR Black Yellow Details of Interface Cable Pin No. Signal Color Brown Orange /RTS...
Page 76: Attaching The Antenna To The Antenna Cover Or Antenna Frame
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM) 4.11.3 Attaching the Antenna to the Antenna Cover or Antenna Frame Basically, the Antenna is attached to the Antenna Cover. However, read/write of RFID tag may become more accurate when the Antenna is attached to the Antenna Frame. When attaching the Antenna to the Antenna Cover, use the PT-3x6 Screws.
Page 77 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM) 1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 3) Push the Hook through the rectangle hole with a jeweler’s screw driver or something, and remove the Platen Holder Cover in the direction indicated by the arrow.
Page 78 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM) 6) Remove the following three screws. SMW-3x6 Screw SMW-4x8 Screw 7) Remove the Platen Frame Top from the printer. Platen Frame Top 8) Remove the four screws from the side of the Print Head Block, slightly pull the Head Side Plate, and remove the two Ribbon Guide Shafts.
Page 79 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R) Insert one of the Ribbon Guide Shafts removed in Step 12 into the Ribbon Guide. Rotate the Ribbon Guide Shaft so that its D-cut is in the same orientation with the Ribbon Guide’s D-cut. NOTE: Without doing this, the Ribbon Guide cannot be fit in the Print Head Block.
Page 80: Attaching The Rfid Module
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R) 4.11.5 Attaching the RFID Module Raise the Print Head Block, and slide the Antenna Frame into the printer as shown below. Let the protruding screw of the printer pass through the slit of the Antenna Frame. Screw Slit Antenna Frame...
Page 81 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R) NOTE: Pass the Antenna Cable between the Antenna Frame and the Media Sensor as shown in the picture below. Media Sensor Antenna Cable Antenna Frame Push the Antenna Cover backward, and secure it with the two SMW-3x6 screws. Antenna Cover including Antenna SMW-3x6 Screw...
Page 82 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM/QM-R) Attach the Cable Clamp to and fit the Bush into the positions shown in the picture below. Pass the Antenna Cable through the Bush, and fix the cable with the Cable Clamp Cable Cable Clamp...
Page 83 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.11 RFID MODULE (B-9704-RFID-H1-QM) Connect the RFID Cable of the RFID Module to CN14 on the Main PC Board. CN14 Main PC Board RFID Cable RFID Module 9) Connect the Antenna Cable to the RFID Module until it clicks. To prevent the Antenna Cable from being caught in the Side Panel (L) or Fan Motor, fold the cable and fix it with the two Cable Clamps.
Page 84: Parameter Setting And Operation Check For The Rfid Module
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date: Jan. 19, 2007) 4.11 RFID MODULE (B-9704-RFID-H1-QM) 4.11.6 Parameter Setting and Operation Check for the RFID Module After installing the RFID Module in the printer, set the parameters for the RFID and perform an operation check by using the following procedures.
Page 85: Swing Cutter (B-4205-Qm-Qm
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 4.12 SWING CUTTER (B-4205-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation •...
Page 86 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 3) Remove the four B-4x5 screws from the side panel (L). 4) Open the top cover and remove the three P-4x8 screws that secure the side panel (L). Top Cover B-4x5 Screw Side Panel (L) B-4x5 Screw...
Page 87 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 9) Raise the print head block until it stops. Print Head Block Stopper 10) Attach the cutter unit to the front of the printer with the cutter attachment screws and the FL-4x6 screw. FL-4x6 Screw Cutter Unit Cutter Attachment Screw...
Page 88 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 13) Insert the cutter harness into the gap between the cutter unit and the printer, and then into the hole in the main frame. Fit the bush into the hole. Main Frame Hole 14) Close the print head block and ribbon shaft holder plate.
Page 89 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 4.12.3.2 Installing the Swing Cutter Module on the B-SX5T Series Since the strip module is standard on the B-SX5T series, it is necessary to remove the rewinder guide plate, strip sensor, etc.
Page 90 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 5) Lift the side panel (L) and put it aside. 6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L). Fan Motor Harness CN19 Side Panel (L)
Page 91 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) Disconnect the operation panel harness from the operation panel ass’y. Operation Panel Ass’y Operation Panel Harness Hook 11) Turn the head lever clockwise to Free position. 12) Open the ribbon shaft holder plate. Ribbon Shaft Holder Plate Head Lever Lock position...
Page 92 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 13) Raise the print head block until it stops. Print Head Block Stopper 14) Remove the two SMW-4x8 screws that secure the strip sensors (TR) and (LED). 15) Release the strip sensor (LED) harness from the cable clamp, and disconnect it from the shorter harness of the strip sensor harness (TR).
Page 93 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 16) Remove the Expansion I/O board from the printer temporarily using the following procedure. (1) Disconnect the Expansion I/O cable from CN1 on the Expansion I/O board. (2) Remove the two B-3x6 screws to detach the Expansion I/O board from the printer. Expansion I/O Board Rear Plate B-3x6 Screw...
Page 94 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 19) Reassemble the operation panel ass’y and the expansion I/O board in the reverse order of removal. 20) Attach the cutter unit to the front of the printer with the cutter attachment screws and the FL-4x6 screw. Cutter Unit FL-4x6 Screw Cutter Attachment Screw...
Page 95 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.12 SWING CUTTER (B-4205-QM-R) 24) Close the print head block and ribbon shaft holder plate. NOTE: DO NOT excessively push down the print head block to close it. Doing so may cause a failure of the print head block or damage to the print head.
Page 96: Rotary Cutter (B-8204-Qm
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 4.13 ROTARY CUTTER (B-8204-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation •...
Page 97 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 3) Remove the four B-4x5 screws from the side panel (L). 4) Open the top cover and remove the three P-4x8 screws that secure the side panel (L). Top Cover B-4x5 Screw Side Panel (L) B-4x5 Screw...
Page 98 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 8) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively. Harness Ass’y CN7 (9 pins) CN9 (2 pins) 9) Fit the bush to the harness ass’y in the orientation as shown below.
Page 99 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 4.13.3.2 Installing the Rotary Cutter Unit on the B-SX5T Series Since the strip module is standard on the B-SX5T series, it is necessary to remove the rewinder guide plate, strip sensor, etc. before installing the cutter module. 1) Turn the power off and disconnect the power cord.
Page 100 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 5) Lift the side panel (L) and put it aside. 6) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L). Side Panel (L) Fan Motor Harness CN19...
Page 101 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) Disconnect the operation panel harness from the operation panel ass’y. Operation Panel Ass’y Operation Panel Harness Hook 11) Turn the head lever clockwise to Free position. 12) Open the ribbon shaft holder plate. Ribbon Shaft Holder Plate Head Lever Lock position...
Page 102 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 13) Raise the print head block until it stops. Print Head Block Stopper 14) Remove the two SMW-4x8 screws that secure the strip sensors (TR) and (LED). 15) Release the strip sensor (LED) harness from the cable clamp, and disconnect it from the shorter harness of the strip sensor harness (TR).
Page 103 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 16) Remove the Expansion I/O board from the printer temporarily using the following procedure. ① Disconnect the Expansion I/O cable from CN1 on the Expansion I/O board. ② Remove the two B-3x6 screws to detach the Expansion I/O board from the printer. Expansion I/O Board Rear Plate B-3x6 Screw...
Page 104 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 20) Fix the cutter drive unit to the printer with the three SM-4x8 screws. SM-4x8 Screw Cutter Drive Unit SM-4x8 Screw 21) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter driver unit, respectively.
Page 105 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 24) Fix the harness ass’y with the clamp. 25) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the Main PC Board Main PC board, respectively.
Page 106 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.13 ROTARY CUTTER (B-8204-QM-R) 27) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three SM-4x8 screws. SM-4 x 8 Screw Cutter Unit SM-4 x 8 Screw Notch Notch...
Page 107: Strip Module (B-9904-H-Qm
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) 4.14 STRIP MODULE (B-9904-H-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.
Page 108: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) 4.14.3 Installation Procedure 1) Turn the power off and disconnect the power cord. 2) Remove the two black screws to detach the front plate. Front Plate Black Screw NOTE: Retain the two black screws and front plate. 3) Remove the four B-4x5 screws from the side panel (L).
Page 109 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) 7) Remove the SM-4x8 screw that secures the operation panel ass’y. SM-4x8 Screw 8) Half open the top cover, otherwise the operation panel ass’y cannot be removed from the printer. Top Cover Operation Panel Ass’y 9) Lift the operation panel ass’y to release the hook, and then remove the operation panel ass’y by...
Page 110 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) 11) Attach the rewind paper guide to the base with the two SMW-4x8B screws. Rewind Paper Guide SMW-4x8B Screw Screw Hole 12) Align the notch of the take-up holder with the screw hole of the rewinder ass’y, and attach them to the printer with the four SM-4x8B screws and the SM-4x8C screw.
Page 111 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) Insert the longer harness of the rewind full sensor (Tr) into the hole in the printer frame. Fit the bush into the hole. Frame Bush Hole Longer Harness of the Rewind Full Sensor (Tr) 16) Connect the longer harness of the rewind full sensor (Tr)and the rewinder harness to CN4 and CN15 on the Main PC board.
Page 112 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) NOTES: 1. You should change the selection switch setting depending on the issue mode. Improper setting may affect the print quality. STANDARD/PEEL OFF (STRIP): Batch or strip mode REWINDER: Built-in rewinder mode For the cut mode, the selection switch can be set to either position.
Page 113 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) 20) Raise the print head block until it stops. Print Head Block Stopper 21) Secure the strip sensor (LED) and strip sensor (Tr) to the printer with the SMW-4x8B screws. 22) Connect the shorter harness of the strip sensor (Tr) to the strip sensor harness (for LED).
Page 114 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) Fix the connected strip sensor harness (for LED) to the base with the cable clamp. While passing the other strip sensor harness through the cut and the bush, reassemble the operation panel ass’y to the printer.
Page 115 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) Fix the strip sensor harness with the three cable clamps and connect it to CN20 on the Main PC board. Main PC Board CN20 Cable Clamp Strip Sensor Harness 25) Reassemble the side panel (L) in the reverse order of removal.
Page 116 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.14 STRIP MODULE (B-9904-H-QM-R) 29) Adjustment If the label skews when using the built-in rewinder unit, turn the adjustment knob of the rewinder guide plate to correct the media feed. Clockwise turn moves the rewinder guide plate forward and counterclockwise turn moves it backward.
Page 117: Ribbon Saving Module (B-9904-R2-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.
Page 118: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) 4.15.3 Installation Procedure 1) Turn the power off and disconnect the power cord. 2) Remove the four B-4x5 screws from the side panel (L). 3) Open the top cover and remove the three P-4x8 screws that secure the side panel (L). Top Cover B-4x5 Screw Side Panel (L)
Page 119 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) 6) Remove the SM-4x8 screw that secures the operation panel ass’y. SM-4x8 Screw 7) Half open the top cover, otherwise the operation panel ass’y cannot be removed from the printer. Operation Panel Ass’y Top Cover 8) Lift the operation panel ass’y to release the hook, and then remove the operation panel ass’y by...
Page 120 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) NOTE: Pass the operation panel harness through the cord bush so that it is not pinched by the side panel (L) when reassembled. Operation Panel Harness Cord Bush 10) Fit the three locking supports into the RSV PC board.
Page 121 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) 12) Insert folded tag paper (1.5-mm thick) between the print head and the platen, and then turn the head lever to Lock position. Insert the head up arm into the plunger of the solenoid. While holding down the head up arm slightly, lift the solenoid.
Page 122 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.15 RIBBON SAVING MODULE (B-9904-R2-QM-R) 14) Connect the solenoid harness to CN1 on the RSV PC board and CN11 on the Main PC board. Pass the solenoid harness through the cut. 15) Connect the solenoid cable to CN2 on the RSV PC board. Main PC Board CN11 RSV PC Board...
Page 123: Pcmcia Interface Board (B-9700-Pcm-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.16 PCMCIA INTERFACE BOARD (B-9700-PCM-QM-R) 4.16 PCMCIA INTERFACE BOARD (B-9700-PCM-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.
Page 124: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.16 PCMCIA INTERFACE BOARD (B-9700-PCM-QM-R) 4.16.3 Installation Procedure 1) Turn the power off and disconnect power cord. 2) Remove the four B-4x5 screws from the side panel (L). 3) Open the top cover and remove the three P-4x8 screws that secure the side panel (L). Top Cover B-4x5 Screw Side Panel (L)
Page 125 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.16 PCMCIA INTERFACE BOARD (B-9700-PCM-QM-R) 7) In case of the B-SX5T or the B-SX4T that the optional Expansion I/O board (B-7704-IO-QM-R) has been installed in, remove the Expansion I/O board from the printer temporarily using the following procedure.
Page 126 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.16 PCMCIA INTERFACE BOARD (B-9700-PCM-QM-R) 10) Secure the PCMCIA interface board to the PCB support plate with the SM-3x6 screw. Tighten the two M-3x5 screws that were loosened previously. (Refer to Caution) PCB Support Plate M-3x5 Screw SM-3x6 screw PCMCIA Interface Board...
Page 127: Usb Interface Board (B-9700-Usb-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.17 USB INTERFACE BOARD (B-9700-USB-QM-R) 4.17 USB INTERFACE BOARD (B-9700-USB-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.
Page 128: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.17 USB INTERFACE BOARD (B-9700-USB-QM-R) 4.17.3 Installation Procedure 1) Turn the power off and disconnect the power cord. 2) Remove the four B-4x5 screws from the side panel (L). 3) Open the top cover and remove the three P-4x8 screws that secure the side panel (L). Top Cover B-4x5 Screw Side Panel (L)
Page 129 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.17 USB INTERFACE BOARD (B-9700-USB-QM-R) 7) If the PCMCIA interface board is used together with the USB interface board, attach the PCB attachment plate to the plate to which the PCMCIA interface board is secured with the SM-3x6 screw.
Page 130 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.17 USB INTERFACE BOARD (B-9700-USB-QM-R) 10) Tighten the two M-3x5 screws of the USB interface board that were loosened previously. (Refer to Caution) 11) Secure the USB interface board to the PCB support plate (when connecting to the Main PC board) or PCB attachment plate (when connecting to the PCMCIA interface board) with the SM-3x6 screw.
Page 131: Lan Interface Board (B-9700-Lan-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.18 LAN INTERFACE BOARD (B-9700-LAN-QM-R) 4.18 LAN INTERFACE BOARD (B-9700-LAN-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.
Page 132: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.18 LAN INTERFACE BOARD (B-9700-LAN-QM-R) 4.18.3 Installation Procedure 1) Turn the power off and disconnect power cord. 2) Remove the four B-4x5 screws from the side panel (L). 3) Open the top cover and remove the three P-4x8 screws that secure the side panel (L). Top Cover B-4x5 Screw Side Panel (L)
Page 133 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.18 LAN INTERFACE BOARD (B-9700-LAN-QM-R) 6) If the PCMCIA interface board is also installed, attach the PCB attachment plate to the plate to which the PCMCIA interface board is secured with the SM-3x6 screw. If not, go to the next step. PCMCIA Interface Board PCB Attachment Plate SM-3x6 Screw...
Page 134 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.18 LAN INTERFACE BOARD (B-9700-LAN-QM-R) 9) Tighten the two M-3x5 screws on the LAN interface board that were loosened previously. (Refer to Caution) 10) Secure the LAN interface board to the PCB support plate (when connecting to the Main PC board) or PCB attachment plate (when connecting to the PCMCIA interface board) with the SM-3x6 screw.
Page 135: Expansion I/O Interface Board (B-7704-Io-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.19 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM-R) 4.19 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution. • Manual instructions must be followed when installing option kits or adding cables to avoid system failures and to insure proper performance and operation.
Page 136 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.19 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM-R) 4) Lift the side panel (L) and put it aside. 5) Disconnect the fan motor harness from CN19 on the Main PC board, and then separate the side panel (L).
Page 137 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.19 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM-R) 9) Secure the expansion I/O board to the rear plate with the two B-3x6 screws removed in Step 7. 10) Connect the expansion I/O cable to CN1 on the expansion I/O board. Expansion I/O Board Rear Plate B-3x6 Screw...
Page 138: Fanfold Paper Guide Module (B-4905-Ff-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B 4.20 FAN FOLD PAPER GUIDE MODULE (B-4905-FF-QM-R) 4.20 FANFOLD PAPER GUIDE MODULE (B-4905-FF-QM-R) WARNING! Disconnect the power cord before installing the Fanfold Paper Guide Module. 4.20.1 Applicable Model This optional device is the fan fold paper guide, which is intended for the following models: B-SX4T-QM-R Series, B-SX5T-QM-R Series 4.20.2 Packing List All the following parts are supplied with the kit.
Page 139: Wireless Lan Module (B-9700-Wlan-Qm-R)
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 18, 2006) 4.21 WIRELESS LAN MODULE (B-9700-WLAN-QM-R) 4.21 WIRELESS LAN MODULE (B-9700-WLAN-QM-R) WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution.
Page 140: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 18, 2006) 4.21 WIRELESS LAN MODULE (B-9700-WLAN-QM-R) NOTES: 1. DO NOT CHANGE the DIP Switch settings on the Wireless LAN Board. Doing so may cause a malfunction. 2. MAC address of the Wireless LAN module will be necessary when setting the MAC address filtering function of an access point.
Page 141 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 18, 2006) 4.21 WIRELESS LAN MODULE (B-9700-WLAN-QM-R) 3) Lift the Side Panel (L) and put it aside. Disconnect the Fan Motor Harness from CN19 on the Main PC Board, and then separate the Side Panel (L). Fan Motor Harness Connector CN19 Side Panel (L)
Page 142 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 18, 2006) 4.21 WIRELESS LAN MODULE (B-9700-WLAN-QM-R) 6) Secure the WLAN Support Plate to the following position with the SMW-3x6 screw. SMW-3x6 Screw WLAN Support Plate PCB Attachment Plate Connect the Wireless LAN Power Cable to CN101 on the LAN Board. Connector CN101 Wireless LAN Power Cable LAN Board...
Page 143 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 18, 2006) 4.21 WIRELESS LAN MODULE (B-9700-WLAN-QM-R) 9) Attach the Antenna Cover to the printer back with the SMW-3x6 screw, as shown below. Pass the LAN Cable through the cut of the Antenna Cover. LAN Board Connector SMW-3x6 Screw Antenna Cover...
Page 144: Rfid Module (B-Sx704-Rfid-U2-Eu-R)
If a use of this product should be likely to have affected medical equipment, immediately turn off the product and contact your TOSHIBA TEC sales agent. Keep a printer embedded with this product at least 23cm away from a person with an implanted cardiac pacemaker or implantable cardioverter-defibrillator.
Page 145: Applicable Model
EU member states and EFTA member states B-SX704-RFID–U2-EU-R (Center frequency: 869.85MHz) 4.22.2 Packing List If any part is missing, please contact your TOSHIBA TEC sales agent. • Antenna Ass’y (1 pc.) •RFID R/W Module (1 pc.) • Antenna Frame • Ribbon Guide (1 pc.) •...
Page 146: Installation Procedure
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) The following parts are required when short-pitch tags (20 mm) are used. Keep them safe when not in use. • Shield Plate (1 pc.) •...
Page 147 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Remove the backing tapes from the reverse side of the Shield Sheet and attach it to the Antenna Cover, as shown below. Shield Sheet Shield Sheet Antenna Cover...
Page 148 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 4.22.3.2 Preparing for the RFID Module Installation Turn the power off and disconnect the Power Cord. Remove the two Black Screws to detach the Front Plate. Black Screws Front Plate...
Page 149 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Lift the Side Panel (L) and put it aside. Disconnect the Fan Motor Harness from CN19 on the Main PC Board, and then remove the Side Panel (L).
Page 150 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Open the Print Head Block and lock it with the Latch. Latch Print Head Block 10. Push the Hook through the rectangle hole with a jeweler’s screw driver or something, and remove the Platen Holder Cover in the direction indicated by the arrow.
Page 151 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 12. Remove the Platen and the Platen Holder in the direction of the arrows 1 to 3 as shown below. Platen Platen Holder 13. Remove the following three screws. SMW-4x8 Screw SMW-3x6 Screw 4-134...
Page 152 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 14. Remove the Platen Frame Top from the printer. Platen Frame Top 15 Remove the four screws from the side of the Print Head Block, slightly pull the Head Side Plate, and remove the two Ribbon Guide Shafts.
Page 153 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 17. Rotate the Ribbon Guide Shaft so that its D-cut is in the same orientation with the Ribbon Guide’s D- cut. Without doing this, the Ribbon Guide cannot be fit in the Print Head Block. Ribbon Guide Shaft’s D-cut Ribbon Guide’s D-cut 18.
Page 154 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 19. Close the Ribbon Shaft Holder Plate, and tighten the two screws, which were temporarily tightened in Step 18, while holding down the Print Head Block. Print Head Block Ribbon Shaft Holder Plate...
Page 155 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 4.22.3.3 Attaching the Antenna Frame and the Antenna Ass’y This section describes the procedure for attaching the Antenna Frame and the Antenna Ass’y. When short-pitch tags (20 mm) are used, the procedure is different from the following. Skip step (1) and go to step (2).
Page 156 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Secure the Antenna Frame with the three screws removed in Step 13 of Section 4.22.3.2. SMW-4x8 Screw SMW-3x6 Screw Connect the Antenna Cable to the Antenna Ass’y until it clicks. Antenna Cable Antenna Ass’y Connector...
Page 157 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Pass the Antenna Cable between the Sensor Block and the Antenna Frame, as shown below. Sensor Block Antenna Cable Antenna Frame Fit the Antenna Ass’y in the Antenna Frame. Be sure to fit the locating pins of the Antenna Cover into the oval holes and the cuts in the Antenna Frame.
Page 158 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Push the Antenna Ass’y in the arrow-indicating direction, and secure it with the two SMW-3x6 screws. Antenna Ass’y SMW-3x6 Screw Go to Section 4.22.3.4 and attach the RFID Module. When using short-pitch tags (20 mm) Attach the Antenna Frame, to which the Shield Plate was attached in Section 4.22.3.1, to the printer in the same way as described in Step 1 of “(1) When using RFID tags other than short-pitch type”.
Page 159 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Connect the Antenna Cable to the Antenna, to which the Antenna Plates were attached in Section 4.22.3.1, until it clicks. Antenna Cable Connector Antenna Secure the Antenna to the Antenna Frame with the P-3x6 screws.
Page 160 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Refer to Steps 5 and 6 in “(1) When using RFID tags other than short-pitch type” and attach the Antenna Cover, to which the Shield Sheet was attached in Section 4.22.3.1, to the Antenna Frame with the SMW-3x6 screws.
Page 161 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Pass the Antenna Cable through the Bush, and fasten the cable with the Cable Clamp. Cable Clamp Antenna Cable Bush Attach the RFID Module to the RFID Attachment Plate A and the RFID Attachment Plate B with the three SMW-3x6 screws.
Page 162 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Fold the Antenna Cable and fasten it with the Cable Clamp together with the other cables to prevent the Antenna Cable from being caught in the Side Panel (L) or Fan Motor. Antenna Cable Cable Clamp Antenna Cable...
Page 163 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Connect the RFID Module to CN14 on the Main PC Board with the Interface Cable. Connector CN14 Main PC Board Connector Interface Cable RFID Module Re-install the Platen, Platen Holder, Strip Plate, and Platen Holder Cover in the reverse order of removal.
Page 164 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 4.22.4 RFID Module Settings After installing the RFID Module on the printer, configure the RFID module settings using the system mode on the printer. Turn on the printer while holding down the [FEED] and [PAUSE] keys at the same time.
Page 165 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Continued from the previous page. <10>RFID RFID tag type setting menu is displayed. TAG NONE Choose “EPC C1 Gen2: 24” with the [FEED] or [RESTART] key. [RESTART] NONE: When a tag type is not selected.
Page 166 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Continued from the previous page. Read retry timeout setting menu is displayed. <10>RFID Set the timeout period during which RFID tag read retries are allowed, with the [FEED] or R CYCLE TIM [RESTART] key.
Page 167 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Continued from the previous page. Radio output power level setting menu is displayed. <10>RFID When the value is “9”, the power is the weakest, and when “18”, the power is the strongest. POWER LEVEL 18 The factory default setting is “18”.
Page 168 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Continued from the previous page AGC threshold for data write setting menu is displayed. <10>RFID When the Q value is set to 1 or greater, the AGC threshold for data write becomes effective. WT AGC When the obtained gain of an RFID tag is lower than the AGC thresholdfor data write, data write is not performed.
Page 169 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) 2） Start the printer in the system mode and perform a read test to measure the AGC value. To measure the AGC value, place only one RFID tag on the Antenna. Example RFID Tag Turn the printer on while holding down the...
Page 170 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Apr. 24, 2008) 4.22 RFID MODULE (B-SX704-RFID-U2-EU-R) Continued from the previous page <10>RFID Press the [PAUSE] key to implement a read test. READ TEST [PAUSE] <10>RFID READING•••. 3132333435363738 Read data is displayed. 39304142 (0A) Data in parentheses ( ) is the AGC value expressed in hex.
Page 171: Rfid Module (B-Sx704-Rfid-U2-Au-R)
If a use of this product should be likely to have affected medical equipment, immediately turn off the product and contact your TOSHIBA TEC sales agent. Keep a printer embedded with this product at least 23cm away from a person with an implanted cardiac pacemaker or implantable cardioverter-defibrillator.
Page 172: Applicable Model
UHF 918.25 to 925.75MHz B-SX704-RFID–U2-AU-R Australia (Center frequency: 922MHz) 4.23.2 Packing List If any part is missing, please contact your TOSHIBA TEC sales agent. • Antenna Ass’y (1 pc.) •RFID R/W Module (1 pc.) • Antenna Frame • Ribbon Guide (1 pc.) •...
Page 173 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) The following parts are required when short-pitch tags (20 mm) are used. Keep them safe when not in use. • Antenna Plate L (1 pc.) •...
Page 174 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Jul. 15, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Remove the backing tapes from the reverse side of the Shield Sheet and attach it to the Antenna Cover, as shown below. Shield Sheet Shield Sheet Antenna Cover...
Page 175 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 4.23.3.2 Preparing for the RFID Module Installation Turn the power off and disconnect the Power Cord. Remove the two Black Screws to detach the Front Plate. Black Screws Front Plate...
Page 176 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Lift the Side Panel (L) and put it aside. Disconnect the Fan Motor Harness from CN19 on the Main PC Board, and then remove the Side Panel (L).
Page 177 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Open the Print Head Block and lock it with the Latch. Latch Print Head Block 10. Push the Hook through the rectangle hole with a jeweler’s screw driver or something, and remove the Platen Holder Cover in the direction indicated by the arrow.
Page 178 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 12. Remove the Platen and the Platen Holder in the direction of the arrows 1 to 3 as shown below. Platen Platen Holder 13. Remove the following three screws. SMW-4x8 Screw SMW-3x6 Screw 4-161...
Page 179 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 14. Remove the Platen Frame Top from the printer. Platen Frame Top 15 Remove the four screws from the side of the Print Head Block, slightly pull the Head Side Plate, and remove the two Ribbon Guide Shafts.
Page 180 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 17. Rotate the Ribbon Guide Shaft so that its D-cut is in the same orientation with the Ribbon Guide’s D- cut. Without doing this, the Ribbon Guide cannot be fit in the Print Head Block. Ribbon Guide Shaft’s D-cut Ribbon Guide’s D-cut 18.
Page 181 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 19. Close the Ribbon Shaft Holder Plate, and tighten the two screws, which were temporarily tightened in Step 18, while holding down the Print Head Block. Print Head Block Ribbon Shaft Holder Plate...
Page 182 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 4.23.3.3 Attaching the Antenna Frame and the Antenna Ass’y This section describes the procedure for attaching the Antenna Frame and the Antenna Ass’y. When short-pitch tags (20 mm) are used, the procedure is different from the following. Skip step (1) and go to step (2).
Page 183 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Secure the Antenna Frame with the three screws removed in Step 13 of Section 4.23.3.2. SMW-4x8 Screw SMW-3x6 Screw Connect the Antenna Cable to the Antenna Ass’y until it clicks. Antenna Cable Antenna Ass’y Connector...
Page 184 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Pass the Antenna Cable between the Sensor Block and the Antenna Frame, as shown below. Sensor Block Antenna Cable Antenna Frame Fit the Antenna Ass’y in the Antenna Frame. Be sure to fit the locating pins of the Antenna Cover into the oval holes and the cuts in the Antenna Frame.
Page 185 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Push the Antenna Ass’y in the arrow-indicating direction, and secure it with the two SMW-3x6 screws. Antenna Ass’y SMW-3x6 Screw Go to Section 4.23.3.4 and attach the RFID Module. When using short-pitch tags (20 mm) Attach the Antenna Frame to the printer in the same way as described in Step 1 of Section 4.23.3.4.
Page 186 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Connect the Antenna Cable to the Antenna, to which the Antenna Plates were attached in Section 4.23.3.1, until it clicks. Antenna Cable Connector Antenna Secure the Antenna to the Antenna Frame with the P-3x6 screws.
Page 187 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Refer to Steps 5 and 6 in “(1) When using RFID tags other than short-pitch type” and attach the Antenna Cover, to which the Shield Sheet was attached in Section 4.23.3.1, to the Antenna Frame with the SMW-3x6 screws.
Page 188 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Pass the Antenna Cable through the Bush, and fasten the cable with the Cable Clamp. Cable Clamp Antenna Cable Bush Attach the RFID Module to the RFID Attachment Plate A and the RFID Attachment Plate B with the three SMW-3x6 screws.
Page 189 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Fold the Antenna Cable and fasten it with the Cable Clamp together with the other cables to prevent the Antenna Cable from being caught in the Side Panel (L) or Fan Motor. Antenna Cable Cable Clamp Antenna Cable...
Page 190 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Jul. 15, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Connect the RFID Module to CN14 on the Main PC Board with the Interface Cable. Connector CN14 Main PC Board Connector Interface Cable RFID Module Re-install the Platen, Platen Holder, Strip Plate, and Platen Holder Cover in the reverse order of removal.
Page 191 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 4.23.4 RFID Module Settings After installing the RFID Module on the printer, configure the RFID module settings using the system mode on the printer. Turn on the printer while holding down the [FEED] and [PAUSE] keys at the same time.
Page 192 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Continued from the previous page. <10>RFID RFID tag type setting menu is displayed. TAG NONE Choose “EPC C1 Gen2: 24” with the [FEED] or [RESTART] key. [RESTART] NONE: When a tag type is not selected.
Page 193 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Continued from the previous page. Read retry timeout setting menu is displayed. <10>RFID Set the timeout period during which RFID tag read retries are allowed, with the [FEED] or R CYCLE TIM [RESTART] key.
Page 194 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Continued from the previous page. Radio output power level setting menu is displayed. <10>RFID When the value is “9”, the power is the weakest, and when “18”, the power is the strongest. POWER LEVEL 18 The factory default setting is “18”.
Page 195 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Continued from the previous page AGC threshold for data write setting menu is displayed. <10>RFID When the Q value is set to 1 or greater, the AGC threshold for data write becomes effective. WT AGC When the obtained gain of an RFID tag is lower than the AGC thresholdfor data write, data write is not performed.
Page 196 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) 2） Start the printer in the system mode and perform a read test to measure the AGC value. To measure the AGC value, place only one RFID tag on the Antenna. Example RFID Tag Turn the printer on while holding down the...
Page 197 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date May 29, 2008) 4.23 RFID MODULE (B-SX704-RFID-U2-AU-R) Continued from the previous page <10>RFID Press the [PAUSE] key to implement a read test. READ TEST [PAUSE] <10>RFID READING•••. 3132333435363738 Read data is displayed. 39304142 (0A) Data in parentheses ( ) is the AGC value expressed in hex.
Page 198 If a use of this product should be likely to have affected medical equipment, immediately turn off the product and contact your TOSHIBA TEC sales agent. Keep a printer embedded with this product at least 23cm away from a person with an implanted cardiac pacemaker or implantable cardioverter-defibrillator.
Page 199 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 4.24.1 Applicable Model This optional device is intended for the following models: B-SX4T-GS20-QM-R and B-SX5T-TS22-QM-R, RFID ready printer. An RFID Ready printer can be identified by the model name sticker on the front of the printer. Be careful not to install this product in the B-SX4T-GS10-QQ/QQ-US and B-SX5T-TS10-QQ/QQ- US RFID Ready printers.
Page 200 EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 4.24.2 Packing List If any part is missing, please contact your TOSHIBA TEC sales agent. • Antenna Ass’y (1 pc.) •RFID R/W Module (1 pc.) • Antenna Frame • Ribbon Guide (1 pc.) •...
Page 201 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) The following parts have been added to the kit. (Serial Number 2809Axxxxxx or later) Certification Data Certification Sticker (for Taiwan only), (1 sheet) Precaution Sheet Sheet (for Taiwan only), (for Korea only),...
Page 202 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Remove the backing tapes from the reverse side of the Shield Sheet and attach it to the Antenna Cover, as shown below. Shield Sheet Shield Sheet Antenna Cover...
Page 203 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 4.23.3.2 Preparing for the RFID Module Installation Turn the power off and disconnect the Power Cord. Remove the two Black Screws to detach the Front Plate. Black Screws Front Plate...
Page 204 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Lift the Side Panel (L) and put it aside. Disconnect the Fan Motor Harness from CN19 on the Main PC Board, and then remove the Side Panel (L).
Page 205 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Open the Print Head Block and lock it with the Latch. Latch Print Head Block 10. Push the Hook through the rectangle hole with a jeweler’s screw driver or something, and remove the Platen Holder Cover in the direction indicated by the arrow.
Page 206 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 12. Remove the Platen and the Platen Holder in the direction of the arrows 1 to 3 as shown below. Platen Platen Holder 13. Remove the following three screws. SMW-4x8 Screw SMW-3x6 Screw 4-189...
Page 207 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 14. Remove the Platen Frame Top from the printer. Platen Frame Top 15 Remove the four screws from the side of the Print Head Block, slightly pull the Head Side Plate, and remove the two Ribbon Guide Shafts.
Page 208 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 17. Rotate the Ribbon Guide Shaft so that its D-cut is in the same orientation with the Ribbon Guide’s D- cut. Without doing this, the Ribbon Guide cannot be fit in the Print Head Block. Ribbon Guide Shaft’s D-cut Ribbon Guide’s D-cut 18.
Page 209 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 19. Close the Ribbon Shaft Holder Plate, and tighten the two screws, which were temporarily tightened in Step 18, while holding down the Print Head Block. Print Head Block Ribbon Shaft Holder Plate...
Page 210 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 4.24.3.3 Attaching the Antenna Frame and the Antenna Ass’y This section describes the procedure for attaching the Antenna Frame and the Antenna Ass’y. When short-pitch tags (20 mm) are used, the procedure is different from the following. Skip step (1) and go to step (2).
Page 211 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Secure the Antenna Frame with the three screws removed in Step 13 of Section 4.24.3.2. SMW-4x8 Screw SMW-3x6 Screw Connect the Antenna Cable to the Antenna Ass’y until it clicks. Antenna Cable Antenna Ass’y Connector...
Page 212 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Pass the Antenna Cable between the Sensor Block and the Antenna Frame, as shown below. Sensor Block Antenna Cable Antenna Frame Fit the Antenna Ass’y in the Antenna Frame. Be sure to fit the locating pins of the Antenna Cover into the oval holes and the cuts in the Antenna Frame.
Page 213 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Push the Antenna Ass’y in the arrow-indicating direction, and secure it with the two SMW-3x6 screws. Antenna Ass’y SMW-3x6 Screw Go to Section 4.24.3.4 and attach the RFID Module. When using short-pitch tags (20 mm) Attach the Antenna Frame to which the Shield Plate was attached in Section 4.24.3.1, to the printer in the same way as described in Step 1 of Section 4.24.3.3.
Page 214 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Connect the Antenna Cable to the Antenna, to which the Antenna Plates were attached in Section 4.24.3.1, until it clicks. Antenna Cable Connector Antenna Secure the Antenna to the Antenna Frame with the P-3x6 screws.
Page 215 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Refer to Steps 5 and 6 in “(1) When using RFID tags other than short-pitch type” and attach the Antenna Cover, to which the Shield Sheet was attached in Section 4.24.3.1, to the Antenna Frame with the SMW-3x6 screws.
Page 216 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Attach the RFID Module to the RFID Attachment Plate A and the RFID Attachment Plate B with the three SMW-3x6 screws. SMW-3x6 Screw RFID Attachment Plate B RFID Attachment Plate A RFID Module SMW-3x6 Screw...
Page 217 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Connect the Antenna Cable to the RFID Module until it clicks. Connector RFID Module Antenna Cable Connect the RFID Module to CN14 on the Main PC Board with the Interface Cable. Connector CN14 Main PC Board Connector...
Page 218 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Re-install the Front Plate and Side Cover (L) in the reverse order of removal. Do not forget to connect the Fan Motor Cable to CN19 on the Main PC Board. Be careful not to catch any cables in the Side Cover (L).
Page 219 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) 4.24.4 RFID Module Settings After installing the RFID Module on the printer, configure the RFID module settings using the system mode on the printer. Destination Code Setting should be performed in the system mode of the printer according to the destination.
Page 220 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Continued from the previous page. RFID tag type setting menu is displayed. <10>RFID Choose “EPC C1 Gen2: 24” with the [FEED] or [RESTART] key. TAG NONE [RESTART] NONE: When a tag type is not selected.
Page 221 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Continued from the previous page. Read retry timeout setting menu is displayed. <10>RFID Set the timeout period during which RFID tag read retries are allowed, with the [FEED] or R CYCLE TIM [RESTART] key.
Page 222 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Continued from the previous page. Radio output power level setting menu is displayed. <10>RFID When the value is “9”, the power is the weakest, and when “18”, the power is the strongest. POWER LEVEL 18 The factory default setting is “18”.
Page 223 4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012B (Revision Date Feb. 6, 2009) 4.24 RFID MODULE (B-SX704-RFID-U2-US-R) Continued from the previous page AGC threshold for data write setting menu is displayed. <10>RFID When the Q value is set to 1 or greater, the AGC threshold for data write becomes effective. WT AGC When the obtained gain of an RFID tag is lower than the AGC thresholdfor data write, data write is not performed.

This manual is also suitable for:

Tec b-sx4t-gs10-qq-us Tec b-sx4t-gs10-qp Tec b-sx5t-ts10-qq Tec b-sx5t-ts10-qq-us Tec b-sx5t-ts10-qp Tec b-9704-rfid-h1-qm-r ... Show all

Toshiba TEC B-SX4T Series Maintenance Manual

1 Unpacking

2 Printer Installation

3 Note for Optional Equipment Installation /Major Unit Replacement/Maintenance

4 Installation Procedure for Optional Equipment

Quick Links

Related Manuals for Toshiba TEC B-SX4T Series

Summary of Contents for Toshiba TEC B-SX4T Series

This manual is also suitable for:

Table of Contents