YOKOGAWA WT5000 User Manual page 106

:MOTor<x>:SPEed:PULSe
Function Sets or queries the number of pulses of the
revolution signal (pulse input type).
:MOTor<x>:SPEed:PULSe {<NRf>}
Syntax
:MOTor<x>:SPEed:PULSe?
<x> = 1 to 4 (motor number)
<NRf> = 1 to 9999
:MOTOR1:SPEED:PULSE 60
Example
:MOTOR1:SPEED:PULSE?
-> :MOTOR1:SPEED:PULSE 60
Description This command is valid when the revolution signal
input type (:MOTor<x>:SPEed:TYPE) is set to
PULSe (pulse input).
:MOTor<x>:SPEed:RANGe
Function Sets or queries the voltage range of the revolution
signal (analog input type).
Syntax :MOTor<x>:SPEed:RANGe {<Voltage>}
:MOTor<x>:SPEed:RANGe?
<x> = 1 to 4 (motor number)
<Voltage> = 1 V, 2 V, 5 V, 10 V, 20 V
:MOTOR1:SPEED:RANGE 20V
Example
:MOTOR1:SPEED:RANGE?
-> :MOTOR1:SPEED:RANGE 20.0E+00
Description This command is valid when the revolution signal
input type (:MOTor<x>:SPEed:TYPE) is set to
ANALog (analog input).
:MOTor<x>:SPEed:SCALing
Function Sets or queries the rotating speed computation
scaling factor.
Syntax :MOTor<x>:SPEed:SCALing {<NRf>}
:MOTor<x>:SPEed:SCALing?
<x> = 1 to 4 (motor number)
<NRf> = 0.0001 to 99999.9999
:MOTOR1:SPEED:SCALING 1
Example
:MOTOR1:SPEED:SCALING?
-> :MOTOR1:SPEED:SCALING 1.0000
:MOTor<x>:SPEed:TYPE
Function Sets or queries the revolution signal input type.
:MOTor<x>:SPEed:TYPE {ANALog|PULSe}
Syntax
:MOTor<x>:SPEed:TYPE?
<x> = 1 to 4 (motor number)
Example :MOTOR1:SPEED:TYPE ANALOG
:MOTOR1:SPEED:TYPE?
-> :MOTOR1:SPEED:TYPE ANALOG
Description Because the revolution signal input type is
determined by the MTR1 and MTR2 configuration
([:INPut]:MTR<x>[:CONFig] command),
setting the input type with this command is not
necessary.
IM WT5000-17EN
:MOTor<x>:SPEed:UNIT
Function Sets or queries the unit that is added to the
rotating speed computation result.
:MOTor<x>:SPEed:UNIT {<String>}
Syntax
:MOTor<x>:SPEed:UNIT?
<x> = 1 to 4 (motor number)
<String> = Up to 8 characters
:MOTOR1:SPEED:UNIT "rpm"
Example
:MOTOR1:SPEED:UNIT?
-> :MOTOR1:SPEED:UNIT "rpm"
Description This command has no effect on the computation
result.
:MOTor<x>:SSPeed
Function Sets or queries the frequency measurement
source for the synchronous speed (SyncSp)
computation.
Syntax :MOTor<x>:SSPeed {U<x>|I<x>}
:MOTor<x>:SSPeed?
<x> of MOTor<x> = 1 to 4 (motor number)
<x> of U<x>, I<x> = 1 to 7 (element)
:MOTOR1:SSPEED I1
Example
:MOTOR1:SSPEED? -> :MOTOR1:SSPEED I1
:MOTor<x>:SYNChronize
Function Sets or queries the synchronization source for
the rotating speed (Speed) and torque (Torque)
computations.
:MOTor<x>:SYNChronize {U<x>|I<x>|
Syntax
EXTernal|Z1|Z3|NONE}
:MOTor<x>:SYNChronize?
<x> of MOTor<x> = 1 to 4 (motor number)
<x> of U<x>, I<x> = 1 to 7 (element)
EXTernal = External clock input (Ext Clk)
Z1 = Z Phase1 (ChD) (/MTR1 option required)
Z3 = Z Phase3 (ChH) (/MTR2 option required)
NONE = No synchronization source
Example :MOTOR1:SYNCHRONIZE NONE
:MOTOR1:SYNCHRONIZE?
-> :MOTOR1:SYNCHRONIZE NONE
5.14 MOTor Group
1
2
3
4
5
6
7
App
Index
5-73