Motor Group - YOKOGAWA WT5000 User Manual

5.14 MOTor Group

The commands in this group deal with the motor evaluation function.
You can make the same settings and queries that you can on the screen that appears by using Setup menu > Input
(Advanced/Options) tab > Motor/Aux button.
The commands in this group are only valid on models with the motor evaluation function 1 (/MTR1) option.
"MOTor3" and "MOTor4" are valid only on models with the motor evaluation function 2 (/MTR2) option.
:MOTor<x>?
Function Queries all motor evaluation function settings.
:MOTor<x>?
Syntax
<x> = 1 to 4 (motor number)
:MOTor<x>:EANGle?
Function Queries all electrical angle measurement settings.
:MOTor<x>:EANGle?
Syntax
<x> = 1 or 3 (motor number)
Description Electrical angle measurement applies to Motor1
and Motor3.
:MOTor<x>:EANGle:CORRection?
Function Queries all electrical angle correction settings.
Syntax :MOTor<x>:EANGle:CORRection?
<x> = 1 or 3 (motor number)
:MOTor<x>:EANGle:CORRection:AENTer?
Function Queries all automatic electrical angle correction
entry settings.
:MOTor<x>:EANGle:CORRection:AENTer?
Syntax
<x> = 1 or 3 (motor number)
:MOTor<x>:EANGle:CORRection:AENTer[:
EXECute]
Function Executes an automatic electrical angle correction
entry.
:MOTor<x>:EANGle:CORRection:
Syntax
AENTer[:EXECute]
<x> = 1 or 3 (motor number)
:MOTOR<x>:EANGLE:CORRECTION:AENTER:
Example
EXECUTE
Description The measured electrical angle of the target
source (:MOTor<x>:EANGle:CORRection:
AENTer:TARGet) is entered as the correction
value.
5-70
:MOTor<x>:EANGle:CORRection:AENTer:T
ARGet
Function Sets or queries the target source for automatically
entering the electrical angle correction value.
Syntax :MOTor<x>:EANGle:CORRection:AENTer:
TARGet {U<x>|I<x>}
:MOTor<x>:EANGle:CORRection:AENTer:
TARGet?
<x> of MOTor<x> = 1 or 3 (motor number)
<x> of U<x>, I<x> = 1 to 7 (element)
:MOTOR1:EANGLE:CORRECTION:AENTER:
Example
TARGET U1
:MOTOR1:EANGLE:CORRECTION:AENTER:
TARGET?
-> :MOTOR1:EANGLE:CORRECTION:AENTER:
TARGET U1
:MOTor<x>:EANGle:CORRection:CLEar
Function Clears the electrical angle correction value.
Syntax :MOTor<x>:EANGle:CORRection:CLEar
<x> = 1 or 3 (motor number)
:MOTOR1:EANGLE:CORRECTION:CLEAR
Example
:MOTor<x>:EANGle:CORRection[:VALue]
Function Sets or queries the electrical angle correction
value.
:MOTor<x>:EANGle:CORRection[:
Syntax
VALue] {<NRf>}
:MOTor<x>:EANGle:CORRection:VALue?
<x> = 1 or 3 (motor number)
<NRf> = -180.00 to 180.00
:MOTOR1:EANGLE:CORRECTION:VALUE 0
Example
:MOTOR1:EANGLE:CORRECTION:VALUE?
-> :MOTOR1:EANGLE:CORRECTION:
VALUE 0.00
:MOTor<x>:EANGle[:STATe]
Function Sets or queries the on/off status of electrical
angle measurement.
Syntax :MOTor<x>:EANGle[:STATe] {<Boolean>}
:MOTor<x>:EANGle:STATe?
<x> = 1 or 3 (motor number)
:MOTOR1:EANGLE:STATE ON
Example
:MOTOR1:EANGLE:STATE?
-> :MOTOR1:EANGLE:STATE 1
IM WT5000-17EN