YOKOGAWA WT5000 User Manual page 104

:MOTor<x>:EANGle:TRIGger
Function Sets or queries the trigger of the electrical angle
measurement.
:MOTor<x>:EANGle:TRIGger {(NONE|Z1|
Syntax
Z3),(NONE|Z1|Z3)}
:MOTor<x>:EANGle:TRIGger?
<x> = 1 or 3 (motor number)
Z1 = Z Phase1 (ChD) (/MTR1 option required)
Z3 = Z Phase3 (ChH) (/MTR2 option required)
:MOTOR1:EANGLE:TRIGGER Z1,Z1
Example
:MOTOR1:EANGLE:TRIGGER?
-> :MOTOR1:EANGLE:TRIGGER Z1,Z1
Description The selectable patterns are determined depending
on the on/off (:MOTor<x>:EANGle[:STATe])
setting of the electrical angle measurement.
:MOTor<x>:FILTer?
Function Queries all input filter settings.
Syntax :MOTor<x>:FILTer?
<x> = 1 to 4 (motor number)
:MOTor<x>:FILTer[:LINE]
Function Sets or queries the line filter.
:MOTor<x>:FILTer[:LINE] {OFF|
Syntax
<Frequency>}
:MOTor<x>:FILTer:LINE?
<x> = 1 to 4 (motor number)
OFF = Line filter off
<Frequency> = 100 Hz, 500 Hz, 1 kHz (line filter
on; cutoff frequency)
:MOTOR1:FILTER:LINE OFF
Example
:MOTOR1:FILTER:LINE?
-> :MOTOR1:FILTER:LINE OFF
Description This setting applies to revolution signal input and
torque signal input.
This command is valid when the signal input type
(:MOTor<x>{SPEed|TORQue}:TYPE) is set to
ANALog (analog input).
:MOTor<x>:FILTer:NOISe:SPEed
Function Sets or queries the noise filter of the revolution
signal (pulse input type).
:MOTor<x>:FILTer:NOISe:SPEed {OFF|
Syntax
<Frequency>}
:MOTor<x>:FILTer:NOISe:SPEed?
<x> = 1 to 4 (motor number)
OFF = Noise filter off
<Frequency> = 10 kHz, 100 kHz, 1 MHz (noise
filter on; cutoff frequency)
:MOTOR1:FILTER:NOISE:SPEED OFF
Example
:MOTOR1:FILTER:NOISE:SPEED?
-> :MOTOR1:FILTER:NOISE:SPEED OFF
Description This command is valid when the revolution signal
input type (:MOTor<x>:SPEed:TYPE) is set to
PULSe (pulse input).
IM WT5000-17EN
:MOTor<x>:FILTer:NOISe:TORQue
Function Sets or queries the noise filter of the torque signal
(pulse input type).
:MOTor<x>:FILTer:NOISe:TORQue {OFF|
Syntax
<Frequency>}
:MOTor<x>:FILTer:NOISe:TORQue?
<x> = 1 to 4 (motor number)
OFF = Noise filter off
<Frequency> = 10 kHz, 100 kHz, 1 MHz (noise
filter on; cutoff frequency)
:MOTOR1:FILTER:NOISE:TORQUE OFF
Example
:MOTOR1:FILTER:NOISE:TORQUE?
-> :MOTOR1:FILTER:NOISE:TORQUE OFF
Description This command is valid when the torque signal
input type (:MOTor<x>:TORQue:TYPE) is set to
PULSe (pulse input).
:MOTor<x>:PM?
Function Queries all motor output (Pm) settings.
:MOTor<x>:PM?
Syntax
<x> = 1 to 4 (motor number)
:MOTor<x>:PM:SCALing
Function Sets or queries the motor output computation
scaling factor.
Syntax :MOTor<x>:PM:SCALing {<NRf>}
:MOTor<x>:PM:SCALing?
<x> = 1 to 4 (motor number)
<NRf> = 0.0001 to 99999.9999
:MOTOR1:PM:SCALING 1
Example
:MOTOR1:PM:SCALING?
-> :MOTOR1:PM:SCALING 1.0000
:MOTor<x>:PM:UNIT
Function Sets or queries the unit that is added to the motor
output computation result.
:MOTor<x>:PM:UNIT {<String>}
Syntax
:MOTor<x>:PM:UNIT?
<x> = 1 to 4 (motor number)
<String> = Up to 8 characters
:MOTOR1:PM:UNIT "W"
Example
:MOTOR1:PM:UNIT?
-> :MOTOR1:PM:UNIT "W"
Description This command has no effect on the computation
result.
:MOTor<x>:POLE
Function Sets or queries the motor's number of poles.
:MOTor<x>:POLE {<NRf>}
Syntax
:MOTor<x>:POLE?
<x> = 1 to 4 (motor number)
<NRf> = 1 to 99
Example :MOTOR1:POLE 2
:MOTOR1:POLE? -> :MOTOR1:POLE 2
5.14 MOTor Group
1
2
3
4
5
6
7
App
Index
5-71