Siemens CP-8000 User Manual page 48

System Overview
The protocols are available via the respective interfaces at the Master Module.
Firmware Protocol name
CPC80 Remote operation
CPC80 SNMP
CPC80 SysLog client
CPC80 NTP/SNTP
CPC80 RADIUS
103MT0 IEC 60870-5-103 Master
BPPT0 IEC 60870-5-101 point-to-
point
DIAST0 Dial-up traffic Slave
ET83 IEC 61850 Ed. 1 (Client,
Server, GOOSE)
ET84 IEC 60870-5-104
ET85 IEC 61850 Ed. 2 (Client,
Server, GOOSE), Ed. 1
(Client)
UMPMT0 IEC 60870-5-101 Master
UMPST0 IEC 60870-5-101 Slave
AGPMT0 AGP interfacing Master
BMCUT0 Benning MCU ASCII
protocol
COUMT0 IEC 62056-21 (IEC 1107)
Master
DNPST0 DNP3 Slave
DNPMT0 DNP3 Master
DNPiT1 DNP3 TCP/IP Slave
DNPiT2 DNP3 TCP/IP Master
MODST0 MODBUS RTU Slave
MODMT2 MODBUS RTU Master
PCBST0 SAT SK 1703 PCMBA
Slave
RP5UT1 ABB RP570/571 Slave
SMST0 ASCII protocol for SMS
alerting
ST1ST0 Siemens SINAUT-ST1
Slave
TG8ST0 L&G Telegyr 800 Slave
1)
only if Server Ed. 1 is required, else is ET85 to be used
2)
GPRS communication possible via X1, X4 and external GPRS modem
3)
X3 in RS-422 mode
48
Unrestricted
CP-8000
Integrated standard protocols
X1, X4 X2
X1, X4
X1, X4
X1, X4
X1, X4
Equipable standard protocols
X2 X3
3)
X2
X2
X1, X4
1)
2)
X1, X4
X1, X4
X2 X3
X2 X3
Equipable third-party protocols
X2 X3
3)
X2
X2 X3
X2 X3
X2 X3
X1, X4
X1, X4
X2 X3
X2 X3
X2 X3
X2 X3
X2
X2 X3
X2 X3
SICAM A8000 / CP-8000 • CP-8021 • CP-8022 Manual
CP-8021 CP-8022
X1, X4 X2 X1, X4
X1, X4 X1, X4
X1, X4 X1, X4
X1, X4 X1, X4
X1, X4 X1, X4
X2 X3 X2, X6 X3, X6
3)
X2 X2, X6
X2 X2, X6
X1, X4 X1, X4
X1, X4 X1, X4
X1, X4 X1, X4
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
3)
X2 X2, X6
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
X1, X4 X1, X4
X1, X4 X1, X4
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
X2 X2, X6
X2 X3 X2, X6 X3, X6
X2 X3 X2, X6 X3, X6
DC8-037-2.02, Edition 10.2017
X2 X7
X7
X7
X7
X7
3)
X7
3)
, X6